NTP Explained | Network Time Protocol | Cisco CCNA 200-301
Full CCNA Course ➤ Register your interest ➤ https://mailchi.mp/45a8a98de600/certbros-course
How to PASS your CCNA! My Recommended Resources
----------------------------------------------------
📚 Get a great book ➤ https://amzn.to/3f16QA5
📹 Video Course ➤ https://mailchi.mp/45a8a98de600/certbros-course ➤ Register your interest
✔ Practice Exams ➤ https://bit.ly/2XmSjZS ➤ The best exams available for the Cisco CCNA
📚 Recommended Books 📚
----------------------------------------------------
Introduction to Hacking ➤ https://amzn.to/38S7kWl
📹 How do you make videos? 📹
----------------------------------------------------
Animations ➤ https://bit.ly/3cMpxaf
Video editing ➤ https://bit.ly/2LFld0t
Disclaimer: These are affiliate links. If you purchase using these links, CertBros will receive a small commission at no extra charge to you.
----------------------------------------------------
NTP stands for Network Time Protocol. It has the very important job of synchronising clocks over a network.
Time is one of those things that can easily be overlooked. In a network though, have inconsistent time, even just by a few minutes, can cause problems.
Every device on a network will have an internal clock. It's important to keep accurate clocks, otherwise, you may run into issues with correlating logs, SSL certificates, software and the list goes on.
This is where NTP comes in. All of the network devices will sync their clocks to an NTP server which will have the accurate time.
NTP uses a hierarchy system. At the very top, we have the big boys, the MacDaddies. These are highly accurate timekeeping devices such as atomic clocks, GPS or radio clocks. They are known as reference clocks.
NTP uses stratum values to identify the accuracy of a clock.
Stratum levels are between 0-15, with 0 being the most accurate and 15 being the least. Anything above 15 means the accuracy of the clock is not trustworthy.
Stratum 0 clocks do not connect over a network.
They are directly connected to time servers. They then sync their time and date to the reference clock. These are known as Primary time servers.
The way the NTP stratum model works is by adding a 1 to stratum value at each layer. So, these primary time servers have a stratum 1 value. As we go further down the stratum hierarchy, the stratum value increases as the reference clock is further and further away meaning the time is less accurate.
NTP uses UDP port number 123. So that’s nice and easy to remember.
Do you Even CertBros?
--------------------------------------
https://www.certbros.com
Subscribe: https://goo.gl/l999wu
Twitter: https://twitter.com/certbros
Видео NTP Explained | Network Time Protocol | Cisco CCNA 200-301 канала CertBros
How to PASS your CCNA! My Recommended Resources
----------------------------------------------------
📚 Get a great book ➤ https://amzn.to/3f16QA5
📹 Video Course ➤ https://mailchi.mp/45a8a98de600/certbros-course ➤ Register your interest
✔ Practice Exams ➤ https://bit.ly/2XmSjZS ➤ The best exams available for the Cisco CCNA
📚 Recommended Books 📚
----------------------------------------------------
Introduction to Hacking ➤ https://amzn.to/38S7kWl
📹 How do you make videos? 📹
----------------------------------------------------
Animations ➤ https://bit.ly/3cMpxaf
Video editing ➤ https://bit.ly/2LFld0t
Disclaimer: These are affiliate links. If you purchase using these links, CertBros will receive a small commission at no extra charge to you.
----------------------------------------------------
NTP stands for Network Time Protocol. It has the very important job of synchronising clocks over a network.
Time is one of those things that can easily be overlooked. In a network though, have inconsistent time, even just by a few minutes, can cause problems.
Every device on a network will have an internal clock. It's important to keep accurate clocks, otherwise, you may run into issues with correlating logs, SSL certificates, software and the list goes on.
This is where NTP comes in. All of the network devices will sync their clocks to an NTP server which will have the accurate time.
NTP uses a hierarchy system. At the very top, we have the big boys, the MacDaddies. These are highly accurate timekeeping devices such as atomic clocks, GPS or radio clocks. They are known as reference clocks.
NTP uses stratum values to identify the accuracy of a clock.
Stratum levels are between 0-15, with 0 being the most accurate and 15 being the least. Anything above 15 means the accuracy of the clock is not trustworthy.
Stratum 0 clocks do not connect over a network.
They are directly connected to time servers. They then sync their time and date to the reference clock. These are known as Primary time servers.
The way the NTP stratum model works is by adding a 1 to stratum value at each layer. So, these primary time servers have a stratum 1 value. As we go further down the stratum hierarchy, the stratum value increases as the reference clock is further and further away meaning the time is less accurate.
NTP uses UDP port number 123. So that’s nice and easy to remember.
Do you Even CertBros?
--------------------------------------
https://www.certbros.com
Subscribe: https://goo.gl/l999wu
Twitter: https://twitter.com/certbros
Видео NTP Explained | Network Time Protocol | Cisco CCNA 200-301 канала CertBros
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
How SNMP Works - a quick guideWhat is a Server? Servers vs Desktops ExplainedSNMP Explained | Simple Network Management Protocol | Cisco CCNA 200-301FTP (File Transfer Protocol), SFTP, TFTP Explained.Linux Network Time Protocol (NTP)Syslog Explained | Cisco CCNA 200-301VLANs Explained | Cisco CCNA 200-301How a DNS Server (Domain Name System) works.IPv6 Addresses Explained | Cisco CCNA 200-301PortFast + BPDU Guard | STP Optional FeaturesOSPF Multi Area ExplainedNetwork Time Protocol - Video By Sikandar Shaik || Dual CCIE (RS/SP) # 35012CCNA (200-301) Topics: NAT, NTP, & DHCPWhat is a Firewall? | Traditional + Next GenerationEtherChannel Explained | Concept & ConfigurationDHCP Explained - Dynamic Host Configuration ProtocolOSPF Explained | Step by StepNetwork Time ProtocolNTP - Network time protocolFree CCNA | NTP | Day 37 | CCNA 200-301 Complete Course