Benzil dimethyl ketal - Will it polymerize?
I guess more of a lab notes than any conclusive video. Sry, I don't know what am I doing...
Time of MMA plymerization for all samples:
23min | 2-4 | 8% DBMK
30min | 3-4 | 2% DBMK, 0.5% TEA
37min | 2-3 | 4% DBMK
43min | 2-2 | 2% DBMK
47min | 3-3 | 0.5% DBMK, 0.5% TEA
55min | 2-1 | 1% DBMK
120min | 3-2 | 0.2% DBMK, 0.5% TEA
??? | 3-1 | 0.1% DBMK, 0.5% TEA
Each sample was polymerized in 18mm test tube with 3W 400nm LED. Setup was not cooled and temperature rised significantly over time so this was probably also a factor.
I imagine, that in commercial resins the viscosity is modified to limit thermal transfer and mainly evaporation, which is cooling MMA and therefore it polymerizes slower. Also for better application on surfaces obviously. This is quite delicate balance though as you must not boil the MMA, unless they use monomer with higher BP. but dentists use MMA so it must be possible to do.
---
Music: https://inquisitor.bandcamp.com
Видео Benzil dimethyl ketal - Will it polymerize? канала Ilusys Systems
Time of MMA plymerization for all samples:
23min | 2-4 | 8% DBMK
30min | 3-4 | 2% DBMK, 0.5% TEA
37min | 2-3 | 4% DBMK
43min | 2-2 | 2% DBMK
47min | 3-3 | 0.5% DBMK, 0.5% TEA
55min | 2-1 | 1% DBMK
120min | 3-2 | 0.2% DBMK, 0.5% TEA
??? | 3-1 | 0.1% DBMK, 0.5% TEA
Each sample was polymerized in 18mm test tube with 3W 400nm LED. Setup was not cooled and temperature rised significantly over time so this was probably also a factor.
I imagine, that in commercial resins the viscosity is modified to limit thermal transfer and mainly evaporation, which is cooling MMA and therefore it polymerizes slower. Also for better application on surfaces obviously. This is quite delicate balance though as you must not boil the MMA, unless they use monomer with higher BP. but dentists use MMA so it must be possible to do.
---
Music: https://inquisitor.bandcamp.com
Видео Benzil dimethyl ketal - Will it polymerize? канала Ilusys Systems
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Testing DIY spectroscope](https://i.ytimg.com/vi/hOU7Q7A7dAQ/default.jpg)
![Runcam 2 4K version reverse polarity repair](https://i.ytimg.com/vi/yx2c-McL0I4/default.jpg)
![Water and sewage - House reconstruction #3](https://i.ytimg.com/vi/7c3SUwmL0GA/default.jpg)
![Hotplate broke](https://i.ytimg.com/vi/Uh6WDsLBvLU/default.jpg)
![Investigating NaOH contamination of Castner cell](https://i.ytimg.com/vi/TQrSbh7HFag/default.jpg)
![Lab notes - castner mini-cell experimental setup #2](https://i.ytimg.com/vi/s2RfI3i9QEs/default.jpg)
![Invasion of... slugs?](https://i.ytimg.com/vi/R86lOuukcAk/default.jpg)
![Rare L159 sighting](https://i.ytimg.com/vi/AyML7Hh9aVY/default.jpg)
![Making pasta on a grand scale](https://i.ytimg.com/vi/2ZPeVvRZuz4/default.jpg)
![Benzil by benzoin oxidation with HNO3](https://i.ytimg.com/vi/UaSO7wFOags/default.jpg)
![Lab notes - making sodium with experimental setup](https://i.ytimg.com/vi/vJoiBuWK8PM/default.jpg)
![Verniculite board | Quest for heat insulating material. pt 2](https://i.ytimg.com/vi/DtzgoFmyYUs/default.jpg)
![Flying near Synthesia](https://i.ytimg.com/vi/und9xMSmNY0/default.jpg)
![Microswitch toggle circuit](https://i.ytimg.com/vi/_jrrNZMwDAI/default.jpg)
![Ozone generator part 3 + Plans for future](https://i.ytimg.com/vi/ga79XUiV8CU/default.jpg)
![Cheap(est) glassblowing lathe - CAD design in Inventor](https://i.ytimg.com/vi/Cb4P3WYSkJI/default.jpg)
![Cheap(est) glassblowing lathe - CAD design in Inventor Part 2](https://i.ytimg.com/vi/vguukpbg_7I/default.jpg)
![Benzil/Triethylamine - Will it polymerize?](https://i.ytimg.com/vi/t3H2M97JKK0/default.jpg)
![DIY table saw tilting mechanism and overview](https://i.ytimg.com/vi/W1dcic0-LjA/default.jpg)
![Making benzal chloride - Toluene photochlorination](https://i.ytimg.com/vi/AnFvT6Ua040/default.jpg)
![Quest for heat insulating material. pt 1](https://i.ytimg.com/vi/Xj-mL7LsfW4/default.jpg)