SNS 313 Part 2: Finishing the Top, Sides, & Bottom of the Fireball Tool Fixture Plate
We'll finish cutting the top surface to the finish I am looking for. Once the top is finished I'll use the auto down-feed to machine the two ends that are still unfinished. Last, I'll flip the fixture over and cut the bottom flat and parallel to the newly machine top surface. Later on, I will begin working on all of the tapped holes needed to be machined in the fixture.
Visit https://fireballtool.com/ for more information on these fixture plates, and all of the other fine tools that Jason builds. Use promo code ABOM79 to receive 10% off your order.
Official Abom79 Merch store https://www.storefrontier.com/abom79
My Amazon Storefront where you'll find many of the tools and products I use in and out of the shop.
https://www.amazon.com/shop/abom79
Paypal Channel Donation: https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=T325L5JZMY9LY&source=url
Support though Patreon: https://www.patreon.com/abom79
My second YouTube channel where I share my cooking, grilling, BBQ , travel, and explorations.
Abom Adventures https://www.youtube.com/channel/UCS9dTkpL6pPj2nrYjsjnb3A
Видео SNS 313 Part 2: Finishing the Top, Sides, & Bottom of the Fireball Tool Fixture Plate канала Abom79
Visit https://fireballtool.com/ for more information on these fixture plates, and all of the other fine tools that Jason builds. Use promo code ABOM79 to receive 10% off your order.
Official Abom79 Merch store https://www.storefrontier.com/abom79
My Amazon Storefront where you'll find many of the tools and products I use in and out of the shop.
https://www.amazon.com/shop/abom79
Paypal Channel Donation: https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=T325L5JZMY9LY&source=url
Support though Patreon: https://www.patreon.com/abom79
My second YouTube channel where I share my cooking, grilling, BBQ , travel, and explorations.
Abom Adventures https://www.youtube.com/channel/UCS9dTkpL6pPj2nrYjsjnb3A
Видео SNS 313 Part 2: Finishing the Top, Sides, & Bottom of the Fireball Tool Fixture Plate канала Abom79
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
SNS 313 Part 1: Machining the Top Surface of the Fireball Tool Fixture PlateAdjustable V Block P5PUSH LATCH Mechanisms (DIY!)Let's Build A Model Steam Engine! Prep and PlanningMachining a New Arbor for a General Model 350 Table Saw - Part 2ARE ROACHES REALLY THAT BAD??SNS 312: Fireball Tool Fixture Plate, Horizontal Arbor RepairGuess The Most Powerful Screw. Big or Small?How To Use a Steady Rest!ULTIMATE WELDING TABLE REVIEW.SNS 310: Machining a Cast Iron Prism Straight EdgeSealing & Backfilling with FLOWABLE FILL. Shop RepairUnloading the Smith & Mills Shaper Part 2Techniques for Machining Straight Deep Holes -- SHOP GEM --Dado Joinery with Hand Tools - Start Woodworking - Class FiveFlexarm 2" NPT Tap Adaptor Part 1Modern engine control musings and Fixing a FigaroSplitting HatchesDyed Shavings and Total Boat Resin Vase Colab with Pohl Barn2020 Professional Woodworkers Shop Tour