Caterpillar D4 steering clutch and bevel shaft rebuild (part 1 of 2)
Here are the previous videos from this project: https://www.youtube.com/playlist?list=PLkzQBXOwxGo_DZVRcJsvQ2qsB0rQOpH87
Instagram:
https://www.instagram.com/pacific.northwest.hillbilly/
Email:
pacific.northwest.hillbilly@gmail.com
Mail:
PNWH
PO Box 2515
Hillsboro, OR 97123
0:00 Intro
2:16 modifying hydraulic press
5:21 attempt 1
7:35 attempt 2
10:58 bearing removal
16:20 throwout removal
17:11 clutch pack disassembly
21:30 engine ideas
#caterpillar #d47u
Видео Caterpillar D4 steering clutch and bevel shaft rebuild (part 1 of 2) канала Pacific Northwest Hillbilly
Instagram:
https://www.instagram.com/pacific.northwest.hillbilly/
Email:
pacific.northwest.hillbilly@gmail.com
Mail:
PNWH
PO Box 2515
Hillsboro, OR 97123
0:00 Intro
2:16 modifying hydraulic press
5:21 attempt 1
7:35 attempt 2
10:58 bearing removal
16:20 throwout removal
17:11 clutch pack disassembly
21:30 engine ideas
#caterpillar #d47u
Видео Caterpillar D4 steering clutch and bevel shaft rebuild (part 1 of 2) канала Pacific Northwest Hillbilly
Показать
Комментарии отсутствуют
Информация о видео
2 декабря 2021 г. 5:15:06
00:23:43
Другие видео канала
![Rebuilding an excavator engine: prepping the block (Hitachi EX120-2/Isuzu 4BD1T)](https://i.ytimg.com/vi/O3vYJ_08g1Q/default.jpg)
![Excavator valve control block assembly - Hitachi EX120-2 rebuild](https://i.ytimg.com/vi/DBC3W4QizSQ/default.jpg)
![Excavator Rebuild: valve control block disassembly - Hitachi EX120-2](https://i.ytimg.com/vi/l_NJ6drnQSQ/default.jpg)
![Caterpillar D4-7U cold start (no pony motor or ether)](https://i.ytimg.com/vi/hrVO2ovJooE/default.jpg)
![Excavator Rebuild: valve block removal - Hitachi EX120-2](https://i.ytimg.com/vi/jFrew0qYyTM/default.jpg)
![Things are looking up!](https://i.ytimg.com/vi/nDgDWGPtACg/default.jpg)
![Removing the stick cylinder using viewer advice - excavator project](https://i.ytimg.com/vi/GWWDsUk75ek/default.jpg)
![Removing and disassembling hydraulic cylinders - excavator project](https://i.ytimg.com/vi/E4Bl5JKHl7Q/default.jpg)
![More bad luck! Excavator engine refresh doesn't go as planned (Isuzu 4BD1T)](https://i.ytimg.com/vi/XJFyAcUbz5A/default.jpg)
![Excavator project - Cab and fuel/hydraulic tank removal, plus visiting a scrapyard](https://i.ytimg.com/vi/aTJc5YULyjc/default.jpg)
![parts run](https://i.ytimg.com/vi/SlNBh6x2YFA/default.jpg)
![9100 hours on this excavator engine...how worn out is it? Isuzu 4BD1T](https://i.ytimg.com/vi/TGlfji99JlM/default.jpg)
![Firewood 2023 - splitting 8 cords of wood in the dark](https://i.ytimg.com/vi/orrpeNJ__ok/default.jpg)
![No going back now! Pulling the engine out of my excavator](https://i.ytimg.com/vi/uWTSAhYqQVI/default.jpg)
![Rebuilding the center joint and more pressure washing - Excavator project](https://i.ytimg.com/vi/L3e7oPuBs5Q/default.jpg)
![Excavator swing device rebuild part 2 of 2 (Hitachi EX120-2)](https://i.ytimg.com/vi/WfjsGhekljo/default.jpg)
![Rebuilding an excavator swing device part 1 of 2 (Hitachi EX120-2)](https://i.ytimg.com/vi/0g2CYpKyaV4/default.jpg)
![Starting the excavator project! Swing device and radiator removal](https://i.ytimg.com/vi/jBihDsIFNOU/default.jpg)
![After 2 years, it's FINALLY done!! Finishing the Caterpillar D4 rebuild](https://i.ytimg.com/vi/mrhT9Oh_keQ/default.jpg)
![Can you spot which hydraulic line I measured wrong? 😂](https://i.ytimg.com/vi/qANPA99rB2o/default.jpg)
![Caterpillar D4 blade fitting and tilt modification](https://i.ytimg.com/vi/AGUZ4fwHKw8/default.jpg)