How to Shine Aluminum - Kevin Caron
#AluminumTips #ShineAluminum #KevinCaronArt
From http://www.kevincaron.com - Artist Kevin Caron shows how to get a mirror shine on aluminum ....
CAUTION: Aluminum dust is very dangerous. A mask and eye protection are musts.
A viewer, Dave, had asked how to shine aluminum since it's a lot different than steel.
Kevin Caron likes to start out with about a 60-grit flap disk on his 4-1/2" angle grinder. He uses it just to clean up the welds - you don't want to touch the base metal. Then he switches to 80 grit to blend in the weld.
After that, you come back and get rid of your grrr marks. That's what you make with the flap disks: grrrs. They're called that because when you look at them, you say, "Grrr!" because you have to grind all of them out again.
Then Kevin Caron goes to a 120-grit sanding pad on some of his woodworking equipment, an electric dual action orbital grinder. Next he uses a 220 grit.
After the sandpaper, he uses Scotch-Brite pads to remove any marks caused by the sanding pads. Kevin Caron shows coarse grit and finer grit Scotch-Brite pads, and there are 4 or 5 grits to allow you to get finer and finer. He attaches the Scotch-Brite pads to an air tool to polish the metal.
To see how to shine the aluminum, Kevin Caron has a piece of 16 gauge 5051 aluminum with some oxidation and grrr marks. He uses the red Scotch-Brite first, but it won't take out the oxidation, so he goes one level back to the electric dual action grinder with 220-grit sandpaper on it - that'll take care of that oxidation!
Kevin Caron shows how the grinder has a dust collector bag on it. Just line up the holes in the sandpaper with the holes in the grinding pad, and it sucks the dust into the bag. The 220 grit takes care of the oxidation, so he goes back to the red, then the finer Scotch-Brite pad.
At this point, you can almost see yourself in the aluminum. Kevin Caron shows the side he has polished in contrast to the other, untouched side.
Kevin Caron says that, if you want to go really crazy, CCW offers a surface preparation pad. He puts one on his angle grinder and shines half of the piece of aluminum to a high reflection using the red surface preparation pad.
You can even go further to polishing compounds, buffing wheels, some rouge, and just go crazy from there.
His best advice: don't put the grrr marks in there in the first place, a real challenge with aluminum and stainless steel.
Kevin Caron is ready to go back to work, so you have time to go to http://www.kevincaron.com to see more how-to videos and his wild work.
Well, you might want to stick around for another moment to see him fly that saucer! ....
"Inspired sculpture for public & private places."
Artist Kevin Caron has been sculpting full time since 2006. See - and hear - his amazing metal and large format 3D-printed sculptures, which are found in public and private places coast-to-coast and online at http://www.kevincaron.com.
Follow me for more fun and facts:
Facebook:
https://www.facebook.com/kevincaronstudios
Instagram: http://www.instagram.com/kevincaronart
Twitter: https://twitter.com/kevincaronart
Видео How to Shine Aluminum - Kevin Caron канала Kevin Caron, Artist
From http://www.kevincaron.com - Artist Kevin Caron shows how to get a mirror shine on aluminum ....
CAUTION: Aluminum dust is very dangerous. A mask and eye protection are musts.
A viewer, Dave, had asked how to shine aluminum since it's a lot different than steel.
Kevin Caron likes to start out with about a 60-grit flap disk on his 4-1/2" angle grinder. He uses it just to clean up the welds - you don't want to touch the base metal. Then he switches to 80 grit to blend in the weld.
After that, you come back and get rid of your grrr marks. That's what you make with the flap disks: grrrs. They're called that because when you look at them, you say, "Grrr!" because you have to grind all of them out again.
Then Kevin Caron goes to a 120-grit sanding pad on some of his woodworking equipment, an electric dual action orbital grinder. Next he uses a 220 grit.
After the sandpaper, he uses Scotch-Brite pads to remove any marks caused by the sanding pads. Kevin Caron shows coarse grit and finer grit Scotch-Brite pads, and there are 4 or 5 grits to allow you to get finer and finer. He attaches the Scotch-Brite pads to an air tool to polish the metal.
To see how to shine the aluminum, Kevin Caron has a piece of 16 gauge 5051 aluminum with some oxidation and grrr marks. He uses the red Scotch-Brite first, but it won't take out the oxidation, so he goes one level back to the electric dual action grinder with 220-grit sandpaper on it - that'll take care of that oxidation!
Kevin Caron shows how the grinder has a dust collector bag on it. Just line up the holes in the sandpaper with the holes in the grinding pad, and it sucks the dust into the bag. The 220 grit takes care of the oxidation, so he goes back to the red, then the finer Scotch-Brite pad.
At this point, you can almost see yourself in the aluminum. Kevin Caron shows the side he has polished in contrast to the other, untouched side.
Kevin Caron says that, if you want to go really crazy, CCW offers a surface preparation pad. He puts one on his angle grinder and shines half of the piece of aluminum to a high reflection using the red surface preparation pad.
You can even go further to polishing compounds, buffing wheels, some rouge, and just go crazy from there.
His best advice: don't put the grrr marks in there in the first place, a real challenge with aluminum and stainless steel.
Kevin Caron is ready to go back to work, so you have time to go to http://www.kevincaron.com to see more how-to videos and his wild work.
Well, you might want to stick around for another moment to see him fly that saucer! ....
"Inspired sculpture for public & private places."
Artist Kevin Caron has been sculpting full time since 2006. See - and hear - his amazing metal and large format 3D-printed sculptures, which are found in public and private places coast-to-coast and online at http://www.kevincaron.com.
Follow me for more fun and facts:
Facebook:
https://www.facebook.com/kevincaronstudios
Instagram: http://www.instagram.com/kevincaronart
Twitter: https://twitter.com/kevincaronart
Видео How to Shine Aluminum - Kevin Caron канала Kevin Caron, Artist
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![How to sand Aluminum?](https://i.ytimg.com/vi/2rxY3nQvcDA/default.jpg)
![Easy Mirror Polish On Steel!](https://i.ytimg.com/vi/n3d9LmAUFlQ/default.jpg)
![Easy Way to Polish Aluminum | POLISHING ALUMINUM](https://i.ytimg.com/vi/9qDC1b-1WhI/default.jpg)
![Orbital Sander Basics | Beginner Tool](https://i.ytimg.com/vi/fXFnzZg-SPo/default.jpg)
![Kitplane Aluminum Gear Polish](https://i.ytimg.com/vi/iMp8sa4Qbr4/default.jpg)
![How to Polish Aluminum](https://i.ytimg.com/vi/JGPreitF4tE/default.jpg)
![How to Use Cutting Oil for Cutting Metal - Kevin Caron](https://i.ytimg.com/vi/hoG_PuEEtaY/default.jpg)
![Are You Sanding Wrong? | How To Sand](https://i.ytimg.com/vi/PspDQOzM09Q/default.jpg)
![Zephyr Polishes FULL Tutorial](https://i.ytimg.com/vi/pCVj4Ph2jgw/default.jpg)
![HOW IT’S MADE (WEILER PIPELINER WIRE WHEEL & SANDING PADS) IMPRESSIVE!](https://i.ytimg.com/vi/-zHlzCuo72M/default.jpg)
![How to Polish Aluminum to a Mirror Finish without Power Tools or Sand Paper!](https://i.ytimg.com/vi/ZgvkyGffkSY/default.jpg)
![How To Sand and Polish Aluminum To Mirror Finish](https://i.ytimg.com/vi/cpMetNWS98E/default.jpg)
![Tricks to Polishing Metal!](https://i.ytimg.com/vi/aTXAHFVItFU/default.jpg)
![Metal polishing difference between 3,000 rpm and 6,000 rpm with Evan's Detailing and Polishing](https://i.ytimg.com/vi/O5_Kx1kJZVw/default.jpg)
![How to sand stainless steel before polishing | coolest polished custom wood pellet grill on earth!](https://i.ytimg.com/vi/VkzJP6Ly3Uc/default.jpg)
![Grinding Discs for Aluminum and Steel - Full Overview](https://i.ytimg.com/vi/HM8Xcif12xI/default.jpg)
![How to Polish ANYTHING with the Dremel Rotary Tool](https://i.ytimg.com/vi/fOT_Q9Xzha0/default.jpg)
![How to choose the right sandpaper for aluminum - Evan's detailing and polishing with Keenan Huppert](https://i.ytimg.com/vi/tkifLQ2wu6c/default.jpg)
![Aluminum Stick Welding - a total success !](https://i.ytimg.com/vi/265inXBQctw/default.jpg)
![How to polish aluminum : pressure and technique](https://i.ytimg.com/vi/jQ-Xt5niKhM/default.jpg)