How to make poor mans fibreglass/fiberglass.
How to make poor mans fibreglass, fiberglass in the USA.
Use waterproof PVA, brush onto surface.
Lay a nylon or polyester mesh netting fabric onto the glued surface.
Rub fabric flat to remove any trapped air between the glue and the fabric.
Brush on another thin layer of waterproof PVA over the fabric.
Allow the PVA to dry.
When the PVA has dried, sand the surface with medium grit sandpaper.
Repeat the above process, glue, fabric, dry, sand then repeat again.
Three or four layers might be enough. The more layers you put on the strong it will become.
A much slower process than using polyester fiberglass or epoxy fiberglass but it gives you an alternative choice.
I hope the video was of use to you.
Subscribe and leave a comment.
Promote your own channel if you like in the comments. I don't mind.
Видео How to make poor mans fibreglass/fiberglass. канала Carving Foam
Use waterproof PVA, brush onto surface.
Lay a nylon or polyester mesh netting fabric onto the glued surface.
Rub fabric flat to remove any trapped air between the glue and the fabric.
Brush on another thin layer of waterproof PVA over the fabric.
Allow the PVA to dry.
When the PVA has dried, sand the surface with medium grit sandpaper.
Repeat the above process, glue, fabric, dry, sand then repeat again.
Three or four layers might be enough. The more layers you put on the strong it will become.
A much slower process than using polyester fiberglass or epoxy fiberglass but it gives you an alternative choice.
I hope the video was of use to you.
Subscribe and leave a comment.
Promote your own channel if you like in the comments. I don't mind.
Видео How to make poor mans fibreglass/fiberglass. канала Carving Foam
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![eps foam cutting tool](https://i.ytimg.com/vi/yDdcW1xpMVs/default.jpg)
![HOW TO CARVE A FOAM ABSTRACT SCULPTURE](https://i.ytimg.com/vi/poSwWrUHPjc/default.jpg)
![Abstract Polystyrene Sculpture Part 02 #shorts](https://i.ytimg.com/vi/GPfQDXZIKmA/default.jpg)
![styrofoam meets acetone #shorts](https://i.ytimg.com/vi/2oYvq9miCKI/default.jpg)
![Hard Coating Polystyrene With Water Proof PVA And Kiln Dried Sand](https://i.ytimg.com/vi/GQvKx1VI-Ps/default.jpg)
![Abstract polystyrene sculpture Part 01 #shorts](https://i.ytimg.com/vi/E-R3Gjjf0XE/default.jpg)
![Carving styrofoam polystyrene with a hacksaw blade](https://i.ytimg.com/vi/-OedXXPJGNo/default.jpg)
![Abstract Polystyrene Sculpture Part 04. #shorts](https://i.ytimg.com/vi/ikJTNJjUnng/default.jpg)
![How to Paint Polystyrene](https://i.ytimg.com/vi/bV2JXnn4M-A/default.jpg)
![Styrofoam Cutting Tool #shorts](https://i.ytimg.com/vi/4f2o4VNyhJU/default.jpg)
![How to carve polystyrene - an abstract polystyrene sculpture #carvingfoam](https://i.ytimg.com/vi/M_RAt855lmU/default.jpg)
![Sand Coated Polystyrene Cube](https://i.ytimg.com/vi/3JKzO5fLnLE/default.jpg)
![DUMDUM POLYSTYRENE SCULPTURE](https://i.ytimg.com/vi/6eziYeqymIc/default.jpg)
![Carving Styrofoam Polystyrene With a Wire Brush.](https://i.ytimg.com/vi/TTEefZOccD8/default.jpg)
![How to Cut Polystyrene With A HOT KNIFE CUTTING TOOL #SHORTS](https://i.ytimg.com/vi/KJPElmwCuSY/default.jpg)
![How to make an Easter Island statue out of polystyrene.](https://i.ytimg.com/vi/L4SicEPDRQ0/default.jpg)
![HOW TO MAKE AN ABSTRACT SCULPTURE](https://i.ytimg.com/vi/dhTh8jlVae0/default.jpg)
![Carving Polystyrene with a hand held Jab Saw](https://i.ytimg.com/vi/Mx2U9j7FQEU/default.jpg)
![HOW TO HARD COAT POLYSTYRENE STYROFOAM WITH PVA AND DRY SAND NOVEMBER 2020](https://i.ytimg.com/vi/OU2MckmSois/default.jpg)
![ABSTRACT POLYSTYRENE SCULPTURE. Part 06. #shorts](https://i.ytimg.com/vi/namOnYGyMjw/default.jpg)
![Abstract Polystyrene Sculpture Part 03 #shorts](https://i.ytimg.com/vi/qReTKAV3wTI/default.jpg)