13" Waterman Aerobile - 1957 Flying Car - Start to Finish

This 13" span Waterman Aerobile started out as a rubber-powered ship in 2004.
Initial trim flights showed that she would be a difficult bird to fly, given the limitations of 
the rubber motor, but I remained hopeful.  But after two seasons of numerous flights and limited success, I decided to switch her over to electric, and I couldn't be happier.  She went from what appeared to be a rubber powered fluttering leaf to a stylish flying car that moved about on rails.

She uses a 7mm pager motor, 30 mah LiPoly, U-80 prop and the Zombie Flight Profiler.  All were placed on a sled using magnets to anchor the unit.  A 1.5" wire extension shaft was attached to the pager motor using the tight fitting insulation from #26 wire.  Doing so allowed me to keep the sleek, tapered design of the tail.

The model came in at 7.9 grams, with the sled weighing an additional 7.5 grams.  Approximately 1.1 grams of ballast was needed on the nose, bringing the all up weight to 16.5 grams.  Wing-loading was .63 gm.psq. in.

I built in a adjustable sliding thrust plate on the sled, but in the end found that the model flew best with zero deflection.  Best intentions...   The first trim session in 2007 left me puzzled, since she flew similarly to the rubber version...that fluttering leaf.  But after some serious pondering, the second trim session a few days later proved very successful.  The positive angle of the elevons was increased, along with a touch of nose weight, and wa-la...she took off on rails in a beautiful climbing circle to the left.  I was so stunned that I was left speechless on the video.  In fact, I became so nervous I could barely keep the camera still.  Talk about night and day, this is about as exciting as it gets for a modeler whose previous 2 years experience with the Aerobile was less than successful or satisfying. 

As I slowly increased the thrust and duration with the Zombie, the little ship began to climb with authority, always in trim with a perfect circling flight.  She even ignored the numerous barn swallows that chased her during the flights.   I flew her for nearly a minute at our small trim field, so I knew it was time to save her for the larger fields of Wawayanda, Geneseo, and Muncie, IN.  There she has flown for her max flights of over two minutes and has placed high in the Power Scale events.  Clearly, Waldo Waterman was smiling down upon us this day.

Photos & film by Tom Hallman & Clive Gamble. Music via MotionArray.com.

*** 10 steps to trimming a rubber model, by John Koptonak: http://www.flyingacesclub.com/PFFT/Trimming10steps.pdf

Plan for the 67" version by Terry Aldrich, which I reduced and simplified: https://outerzone.co.uk/plan_details.asp?ID=1661
Tutorial by Mark Allison on making mini-gearbox drives: http://hallmanstudio.com/Gearbox_tutorial.pdf
Atomic Workshop supplied the Zombie Flight profiler: http://www.atomicworkshop.co.uk/catalog/
Availability may be delayed.

Source for electric supplies in the US: http://microflierradio.com/free-flight.html
Source for electric supplies in the UK: http://www.kpaero.com

Flying Aces Club merchandise: https://www.cafepress.com/flyingacesclub
Center of Gravity merchandise: https://www.cafepress.com/centergravity

For more info on free-flight rubber-powered models, check these websites:
https://brooklyn-balsa.square.site
http://www.easybuiltmodels.com/
http://www.volareproducts.com/BUY/
http://www.flyingacesclub.com
National Free Flight Society - https://freeflight.org/
Mike Stuart's Flying Scale Models - http://www.ffscale.co.uk/
https://www.freeflightsupplies.co.uk

Видео 13" Waterman Aerobile - 1957 Flying Car - Start to Finish канала maxfliart