Hacking a cheap disco light to fire UV beams.
Having modified a few of these cheap disco lights with other hand-made PCBs I decided to get a set of five prototype boards made.
Unlike the original light that pulses and flashes during operation, I decided to make it simple and just have a static pattern of light beams. That allows a very simple circuit to be used to power all the LEDs directly from the mains supply.
In this instance I decided to populate the PCB entirely with near-UV LEDs to project a series of deep violet beams of light through hazy air and create a grid of 64 points of light on a wall.
The really interesting bit is when you wear fluorescent items and walk in front of the light. It makes the material fluoresce as a series of dots on your clothing.
It's an unusual light. It would only be suited to specific events where a lot of suitably reactive colours were being worn. Like a rave or cyber party for instance.
I think the next one I make will have bright golden-white LEDs in it so it is a practical source of light with the advantage of being visually artistic too.
I'd also like to make one with the slow colour changing LEDs, but this application requires clear ones with the standard focussing lens on the front for highest efficiency. The RGB ones have the LEDs offset to the lens inside, so I'd expect to have to angle the whole PCB slightly to focus then through the main lens, and the light from each LED would be in the form of separate RGB beams.
Note that this particular PCB is better suited to higher voltage mains supplies like 220V upwards. For a 120V version it would require that the LEDs were in parallel pairs or two separate sections in parallel with either two power supplies or their own set of series resistors to help divide the current between the two sections. (Or a voltage doubler could be used to boost the voltage.)
The use of phosphor coated LEDs creates a softer beam effect than the laser-like effect of bare chip colours like red, green, amber and blue.
If you enjoy these videos you can help support the channel with a dollar for coffee, cookies and random gadgets for disassembly at:-
http://www.bigclive.com/coffee.htm
This also keeps the channel independent of YouTube's advertising algorithms allowing it to be a bit more dangerous and naughty.
Видео Hacking a cheap disco light to fire UV beams. канала bigclivedotcom
Unlike the original light that pulses and flashes during operation, I decided to make it simple and just have a static pattern of light beams. That allows a very simple circuit to be used to power all the LEDs directly from the mains supply.
In this instance I decided to populate the PCB entirely with near-UV LEDs to project a series of deep violet beams of light through hazy air and create a grid of 64 points of light on a wall.
The really interesting bit is when you wear fluorescent items and walk in front of the light. It makes the material fluoresce as a series of dots on your clothing.
It's an unusual light. It would only be suited to specific events where a lot of suitably reactive colours were being worn. Like a rave or cyber party for instance.
I think the next one I make will have bright golden-white LEDs in it so it is a practical source of light with the advantage of being visually artistic too.
I'd also like to make one with the slow colour changing LEDs, but this application requires clear ones with the standard focussing lens on the front for highest efficiency. The RGB ones have the LEDs offset to the lens inside, so I'd expect to have to angle the whole PCB slightly to focus then through the main lens, and the light from each LED would be in the form of separate RGB beams.
Note that this particular PCB is better suited to higher voltage mains supplies like 220V upwards. For a 120V version it would require that the LEDs were in parallel pairs or two separate sections in parallel with either two power supplies or their own set of series resistors to help divide the current between the two sections. (Or a voltage doubler could be used to boost the voltage.)
The use of phosphor coated LEDs creates a softer beam effect than the laser-like effect of bare chip colours like red, green, amber and blue.
If you enjoy these videos you can help support the channel with a dollar for coffee, cookies and random gadgets for disassembly at:-
http://www.bigclive.com/coffee.htm
This also keeps the channel independent of YouTube's advertising algorithms allowing it to be a bit more dangerous and naughty.
Видео Hacking a cheap disco light to fire UV beams. канала bigclivedotcom
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Making cheap solar garden lights more interesting. (Laid back video.)Rechargeable torch with dangerous charger (with schematics)Safe USB version of the Gillian's Diamonds lamp. (With PCB file.)Mystery Dumpster Teardown - 2020-06-12Building a TRUE 4k home cinema projector (it’s awesome)Heat shrink solder butt connector test.Inside an ionic foot detox spa unit.USB laundry machine for tiny (moist) Chinese panties.I Bought a PALLET of BROKEN PS4's - How Many Can I Fix?This USB bottle generates surface sanitiser from water and salt.Inside a recalled Amazon Basics power bank.How an RCD / GFI works and troubleshooting rogue tripping.USB powered disco light mod and solder reflow disaster.Inside a Znter lithium 9V battery.Teardown of a British electric shower that went bang.INFINITY MIRROR 7 BAND DIGITAL SPECTRUM ANALYZERCrimping tool test that I screwed up. (Read description.)Abandoned Railway Carts - Mystery tapes from a disused comms roomHow to identify diamonds,rubys and opal with a black light