How to Varnish and Refinish a cabin sole - Get A Deep Rich Sole in that sailboat floor
This video goes into detail on the proper way of refinishing the floor in a boat; The cabin sole. These techniques can be used on any floor or any wood surface you are refinishing. Follow these steps and you'll get a long lasting finish. Keep in mind that gloss finishes typically have better UV resistance. Please read the Comments & Watch the video till the end to Get all the tips in Day After Day Finishing.
You can get the tools here And Help us.
Get the Scraper set here: https://amzn.to/2LeuCMr
Rubbed finish Epifanes varnish: https://amzn.to/2WmPZ4B May need more than one.
Gloss Epifanes Varnish: https://amzn.to/2YO5La7 May need more than one.
Cheap Wagner heat gun: https://amzn.to/3fGafpt
Purdy soft brush for finishing: https://amzn.to/35Q0joO
Newer version of Wooster Pro for first 3 coats ish: https://amzn.to/3duIxtK
A Chemical remover. Not the same as I used. Reviews were good: https://amzn.to/2YPX5zW
Sand Paper ,You may need a couple of packs: https://amzn.to/2WLezLr or https://amzn.to/2Wg9gnY
Nitril gloves: https://amzn.to/3dwnMOf
Mixing cups if you use alot: https://amzn.to/3fC6pxd
Mineral Spirits: https://amzn.to/2zuE8YR
“As an Amazon Associate I earn from qualifying purchases.” Thank You! For Helping Us Out.
I put 7-8 coats of gloss total including the sealing coats and then 2 coats of a rubbed finish. so the floors would not be so slippery when wet. the back side was kept a gloss finish to better repel water and dirt from the bilge.
If you decide to strip and refinish your Cabin sole. Remember that if you decide to keep the gloss the floor Will be SLIPPERY WHEN WET.
I recommend applying some sort of grip or just going with a Satin, Matt or rubbed finish on the final two or three coats.
This cabin sole was done in A Rubbed finish which has nothing to do with rubbing. It applies just like the other finishes but does have a slight faster drying time.
when redoing your floor pay attention to the dust in the location you are varnishing. Dust can be very frustrating as most of the bubbles you see are actually trapped dust particles. So make sure your doing all you can to keep dust out.
Learn how to keep your brush fresh
Also use a mask and proper safety gear. I was not and i was spending little time then out. DO NOT BREATH THE FUMES.
PLEASE- LIKE, SUBSCRIBE, COMMENT AND SHARE
& Thank You for Viewing. It all Helps me to bring you guys some More LIFE Videos. Thank You again, It's really appreciated.
Видео How to Varnish and Refinish a cabin sole - Get A Deep Rich Sole in that sailboat floor канала Ripple Life
You can get the tools here And Help us.
Get the Scraper set here: https://amzn.to/2LeuCMr
Rubbed finish Epifanes varnish: https://amzn.to/2WmPZ4B May need more than one.
Gloss Epifanes Varnish: https://amzn.to/2YO5La7 May need more than one.
Cheap Wagner heat gun: https://amzn.to/3fGafpt
Purdy soft brush for finishing: https://amzn.to/35Q0joO
Newer version of Wooster Pro for first 3 coats ish: https://amzn.to/3duIxtK
A Chemical remover. Not the same as I used. Reviews were good: https://amzn.to/2YPX5zW
Sand Paper ,You may need a couple of packs: https://amzn.to/2WLezLr or https://amzn.to/2Wg9gnY
Nitril gloves: https://amzn.to/3dwnMOf
Mixing cups if you use alot: https://amzn.to/3fC6pxd
Mineral Spirits: https://amzn.to/2zuE8YR
“As an Amazon Associate I earn from qualifying purchases.” Thank You! For Helping Us Out.
I put 7-8 coats of gloss total including the sealing coats and then 2 coats of a rubbed finish. so the floors would not be so slippery when wet. the back side was kept a gloss finish to better repel water and dirt from the bilge.
If you decide to strip and refinish your Cabin sole. Remember that if you decide to keep the gloss the floor Will be SLIPPERY WHEN WET.
I recommend applying some sort of grip or just going with a Satin, Matt or rubbed finish on the final two or three coats.
This cabin sole was done in A Rubbed finish which has nothing to do with rubbing. It applies just like the other finishes but does have a slight faster drying time.
when redoing your floor pay attention to the dust in the location you are varnishing. Dust can be very frustrating as most of the bubbles you see are actually trapped dust particles. So make sure your doing all you can to keep dust out.
Learn how to keep your brush fresh
Also use a mask and proper safety gear. I was not and i was spending little time then out. DO NOT BREATH THE FUMES.
PLEASE- LIKE, SUBSCRIBE, COMMENT AND SHARE
& Thank You for Viewing. It all Helps me to bring you guys some More LIFE Videos. Thank You again, It's really appreciated.
Видео How to Varnish and Refinish a cabin sole - Get A Deep Rich Sole in that sailboat floor канала Ripple Life
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Hallberg-Rassy 312 "Ellös": HOW TO MAKE THE BOAT CABIN FLOOR (DIYBoat)Varnish and Epoxy~ a Professional Wood Finish for Teak Part1Varnishing a Boat Deck with Brush and Roller | Pre Season Epifanes Varnish Top UpHow to Repair Your Teak Deck - A 10 Step Easy-To-Follow ProcessSave Your Mortal Sole! | Sailing Balachandra E014TotalBoat Gleam Varnishing TipsHow to replace old interior carpet with synthetic Sea Floor in the salon | MyBoat DIYHow to use Penetrating EpoxyVeneer Repair & Refinishing Furniture: Cocktail CabinetThree Easy Steps On How To Varnish. For Bigginers. Tips And Techniques.Restoring Mahogany & Teak Boat WoodHow I improved the look and feel of my boat, How to install engineered teak on your boatStripping and sanding varnish with a heat gun to prep for new coatsShaving Fiberglass, New Approach To Stress Cracks And Mail Call!How to best prep and varnish your boat - Part 2Life is Like Sailing - Oiling the Cabin TeakVarnish and Epoxy~ Part2IMG 1207 Teak and Holly Flooring Overhaul, "Sailing Adventures with Island Girl"How to Remodel a Sailboat Galley Part 1, Sailboat Galley / Kitchen FixInstalling a Foam Backed Headliner in a Boat