Garage Roller Door 🚪 Installation 🛠️ Guide
A guide on how to install a series A roller door.
--
PART 1: Measuring
1. Measure the width of the opening (between the columns)
2. Mark the center of the opening
3. Use the center point and mark-out the daylight opening of the door
4. This is not the roller door width, as you need to subtract the tracks widths
PART 2: Door Jambs
1. Align the door jamb with the mark on the ground
2. Place a mark where the jamb intersects rafter
3. Extend the mark using combination square
4. Cut along the lines
5. Ensure the jamb is level and on the marked concrete line
6. Tek the jamb on to the rafter
7. Step drill and then bolt
8. Tek the side girts on to the jamb
9. Repeat steps for the other side
PART 3: Footings
1. Tek the roller door footing brackets on to the door jambs
2. Measure & mark 100mm (can differ) from the slab edge
3. Drill the hole for the anchor bolt
4. Hammer in the anchor bolt
5. Tighten using a rattle gun
PART 4: Header
1. Mark the height of the roller door on to the door jambs
2. Tek the header brackets above the mark on the door jamb
3. Tek the header beam on to the header brackets
PART 5: Bracket Arms
1. Measure the radius of the door
2. Use the door radius to place a mark above the header beam
3. Tek the bracket arm in to place
4. Step drill a bolt hole
5. Bolt in to place
6. Ensure brackets are bolted securely. If done incorrectly, it is extremely hazardous
PART 6: Tracks
1. Bend up the track ends, to prevent the door from catching on them
2. Mark the track height
3. Cut to length
4. Attach track brackets
5. Tek the tracks on to the jambs
PART 7: Installing the Door
1. A duct lift is the recommended way to lift a roller door into place
2. If the door is low, muscle can also be used to lift it in to place
3. Screw the roller door in to place
4. Tighten
5. Unwrap the roller door
PART 8: Lock
1. Step drill holes for the lock
2. Check if the door locks, file the holes if it does not
3. Test the lock
DISCLAIMER
A roller door is the largest moving object in a shed. It is dangerous and critical that installation is done correctly.
If you are unsure about anything, we recommended asking a professional to install it instead.
Please take care when installing a roller door and triple check everything.
We take no responsibly for injuries, damage or incorrectly installed doors as a result of the contents in this video.
Please note this is a guide and is not suitable for all door types or manufactures.
--
If you like these types of videos and would like to see more of them, please like/subscribe and let us know what you would like to see :)
--
Perth Wide Custom Steel Shed Suppliers and Builders
Website: https://royssheds.com.au/
Phone: 08 6230 2250
Online Quote: https://royssheds.com.au/request-an-online-shed-quote
---
Song: Nekzlo - Seeking
https://soundcloud.com/nekzlo/seeking-instrumental
Видео Garage Roller Door 🚪 Installation 🛠️ Guide канала Roys Sheds Supplier in Perth & WA
--
PART 1: Measuring
1. Measure the width of the opening (between the columns)
2. Mark the center of the opening
3. Use the center point and mark-out the daylight opening of the door
4. This is not the roller door width, as you need to subtract the tracks widths
PART 2: Door Jambs
1. Align the door jamb with the mark on the ground
2. Place a mark where the jamb intersects rafter
3. Extend the mark using combination square
4. Cut along the lines
5. Ensure the jamb is level and on the marked concrete line
6. Tek the jamb on to the rafter
7. Step drill and then bolt
8. Tek the side girts on to the jamb
9. Repeat steps for the other side
PART 3: Footings
1. Tek the roller door footing brackets on to the door jambs
2. Measure & mark 100mm (can differ) from the slab edge
3. Drill the hole for the anchor bolt
4. Hammer in the anchor bolt
5. Tighten using a rattle gun
PART 4: Header
1. Mark the height of the roller door on to the door jambs
2. Tek the header brackets above the mark on the door jamb
3. Tek the header beam on to the header brackets
PART 5: Bracket Arms
1. Measure the radius of the door
2. Use the door radius to place a mark above the header beam
3. Tek the bracket arm in to place
4. Step drill a bolt hole
5. Bolt in to place
6. Ensure brackets are bolted securely. If done incorrectly, it is extremely hazardous
PART 6: Tracks
1. Bend up the track ends, to prevent the door from catching on them
2. Mark the track height
3. Cut to length
4. Attach track brackets
5. Tek the tracks on to the jambs
PART 7: Installing the Door
1. A duct lift is the recommended way to lift a roller door into place
2. If the door is low, muscle can also be used to lift it in to place
3. Screw the roller door in to place
4. Tighten
5. Unwrap the roller door
PART 8: Lock
1. Step drill holes for the lock
2. Check if the door locks, file the holes if it does not
3. Test the lock
DISCLAIMER
A roller door is the largest moving object in a shed. It is dangerous and critical that installation is done correctly.
If you are unsure about anything, we recommended asking a professional to install it instead.
Please take care when installing a roller door and triple check everything.
We take no responsibly for injuries, damage or incorrectly installed doors as a result of the contents in this video.
Please note this is a guide and is not suitable for all door types or manufactures.
--
If you like these types of videos and would like to see more of them, please like/subscribe and let us know what you would like to see :)
--
Perth Wide Custom Steel Shed Suppliers and Builders
Website: https://royssheds.com.au/
Phone: 08 6230 2250
Online Quote: https://royssheds.com.au/request-an-online-shed-quote
---
Song: Nekzlo - Seeking
https://soundcloud.com/nekzlo/seeking-instrumental
Видео Garage Roller Door 🚪 Installation 🛠️ Guide канала Roys Sheds Supplier in Perth & WA
Показать
Комментарии отсутствуют
Информация о видео
16 июля 2018 г. 5:52:22
00:04:08
Другие видео канала
Shed Colour Combination Visualiser ToolOur new Slitter folder making a barge flashing for a shed we are supplyingHow to assemble and install rafters sections for a gable shedSome really cool pressing !!Roys Sheds.How we make out down pipe pops !2000w Co2 Laser Test Firing - PRC Laser Lab #shorts #laser #co2 #manufacturing #steelHow long can you spin a Tek screw for? #sheds #shortsvideoInstalled some stair in a shed house!4 Different Camera Angles of a Laser Cutter #shorts #lasercutterSlide show of a split skillion shed roof with awnings that we supplied and built!24.5m x 8m x 4m Shed Build at Perth Airport, Cloverdale WA 6105Roys Sheds – a Quick Tour of Our Factory 👍Roys Sheds Constructs 12m x 15m x 4m in Bibra Lake, WA 6163Laser cutting some bottle openers!!15 x 10 Garaport Build Time LapseRoys Sheds Constructs 12m x 9m x 3.6m Shed in Muchea, WA 6501Shed Construction Timelapse Video Compilation in Perth, Western AustraliaPony / Horse Shelter Timelapse in Lower Chittering, WA 6084Kings Road Brewing Co. How we made a sign for them!How to Open an AMIA Window (No Lock) #shorts #howto