Skywalker falcon first flights (so efficient you'll think I'm lying)
Banggood: https://goo.gl/6Hx8Gu
After making this video I tried a flight with a 3S 2200mAh battery, no camera onboard (AUW=634g), and got 70 minutes! This is measured from full charge until the alarm sounds (3.3v under load). The first 1/3 of the flight was slow level cruise at about 40% throttle, the remainder was mostly long slow climbs and glides. Battery cells were at 3.54v a few minutes after landing.
Видео Skywalker falcon first flights (so efficient you'll think I'm lying) канала iforce2d
After making this video I tried a flight with a 3S 2200mAh battery, no camera onboard (AUW=634g), and got 70 minutes! This is measured from full charge until the alarm sounds (3.3v under load). The first 1/3 of the flight was slow level cruise at about 40% throttle, the remainder was mostly long slow climbs and glides. Battery cells were at 3.54v a few minutes after landing.
Видео Skywalker falcon first flights (so efficient you'll think I'm lying) канала iforce2d
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Twin Hopper part 9 (endurance test with 2.4kg li-ion)](https://i.ytimg.com/vi/1AgXsr2m50w/default.jpg)
![Twin hopper part 8 (5kg payload full send)](https://i.ytimg.com/vi/36QGd-YpO8g/default.jpg)
![Twin Hopper part 7 (new motor mounts, 3.6kg payload test)](https://i.ytimg.com/vi/whFEms5EO1M/default.jpg)
![iomixer car tests (steering gyro, launch control and more)](https://i.ytimg.com/vi/dnNDLJeyz7c/default.jpg)
![Twin Hopper part 6 (flight tests: stall, endurance, 2kg payload)](https://i.ytimg.com/vi/0_bcUFK3jl8/default.jpg)
![Electric bike part 11 (attempting 80km ride with extended battery)](https://i.ytimg.com/vi/LB0zH-5ygPk/default.jpg)
![Twin Hopper part 5 (first flights)](https://i.ytimg.com/vi/w6ERSRxfls8/default.jpg)
![What exactly is 'iomixer' ?](https://i.ytimg.com/vi/h-Y8iPSBVRs/default.jpg)
![Twin Hopper part 4 (wing join, hatches, wiring)](https://i.ytimg.com/vi/-1r6j_lNRQo/default.jpg)
![Long range farm chopper](https://i.ytimg.com/vi/7q7cPuqwtxA/default.jpg)
![Starlink first few days (NZ)](https://i.ytimg.com/vi/IIlQ8EnPr0c/default.jpg)
![Arducopter acro mode trial](https://i.ytimg.com/vi/IrP_4XYL4VI/default.jpg)
![iomixer MIDI in, MIDI out](https://i.ytimg.com/vi/AMZ-SkoiGuQ/default.jpg)
![Fiberglass over plywood miniquad, trying some AM32 ESCs](https://i.ytimg.com/vi/277hMj-pEUw/default.jpg)
![Homeslice8 speed check with 7x7 prop (fail)](https://i.ytimg.com/vi/YRIf8nRT7W4/default.jpg)
![Twin Hopper part 3 (outer wings, glassing fuselage)](https://i.ytimg.com/vi/ABdhq0u6ViQ/default.jpg)
![Air Tractor tip vortices](https://i.ytimg.com/vi/QtrIV7VLm-g/default.jpg)
![Twin Hopper part 2 (flaps, fuselage assembly)](https://i.ytimg.com/vi/Q0Aw26VfCSE/default.jpg)
![Twin Hopper part 1 (CNC cutting a lot of foam)](https://i.ytimg.com/vi/j3sqS8J-DwQ/default.jpg)
![Another DIY CNC router, part 12 (limit switches, machining XPS foam)](https://i.ytimg.com/vi/h_yqcbaN5U4/default.jpg)
![Another DIY CNC router, part 11 (wasteboard surfacing, making and testing a wooden prop)](https://i.ytimg.com/vi/Bz_ddh9TKbY/default.jpg)