Keihin butterfly carb rebuild #1
The tips and tricks:
1) Replace the craptastic plastic fuel inlet with brass.
2) There are check-balls in the float bowl and accel pump cap.
3) Don't forget the rubber plug over the intermediate jet.
4) a: Braze a loose choke lever to the shaft.
b: Put an 0-80 screw in the choke lever to keep it open.
c: Assemble to the choke cable with the screw pointing up.
5) Use silicone on the Welch plugs. Clean the idle circuit.
6) Use a rebuild kit with Viton rubber.
7) a: Use the factory choke cable, not a coat hanger.
b: Adjust accel pump volume.
c: Dial in idle speed and idle mixture screws.
8) a: Use support bracket on rubber-band style manifold.
b: Use S&S style manifold clamps.
c: O-rings come in Viton too.
d: Put manifold on by itself before mounting the carb.
e: Tighten manifold clamps before head and cylinder.
9) Use a Fram CA77 in the early Harley air filter.
Transcript: http://www.open-sport.org/Repair/Keihin-carb-repair-1/
Comment at:
http://xlforum.net/vbportal/forums/showthread.php?p=5632791
Help a brother out, some Amazon associate links that pay a percentage of anything you buy during the same browser session.
A rebuild kit with Viton needle:
http://www.amazon.com/exec/obidos/ASIN/B009CA2SEU/cookinexperi-20
Rebuild kit just for accel pump:
http://www.amazon.com/exec/obidos/ASIN/B00HXJAP2O/cookinexperi-20
the Viton O-ring:
http://www.amazon.com/exec/obidos/ASIN//cookinexperi-20
Clamps and O-rings:
http://www.amazon.com/exec/obidos/ASIN/B009BQXBH8/cookinexperi-20
Видео Keihin butterfly carb rebuild #1 канала Open-Sport.org
1) Replace the craptastic plastic fuel inlet with brass.
2) There are check-balls in the float bowl and accel pump cap.
3) Don't forget the rubber plug over the intermediate jet.
4) a: Braze a loose choke lever to the shaft.
b: Put an 0-80 screw in the choke lever to keep it open.
c: Assemble to the choke cable with the screw pointing up.
5) Use silicone on the Welch plugs. Clean the idle circuit.
6) Use a rebuild kit with Viton rubber.
7) a: Use the factory choke cable, not a coat hanger.
b: Adjust accel pump volume.
c: Dial in idle speed and idle mixture screws.
8) a: Use support bracket on rubber-band style manifold.
b: Use S&S style manifold clamps.
c: O-rings come in Viton too.
d: Put manifold on by itself before mounting the carb.
e: Tighten manifold clamps before head and cylinder.
9) Use a Fram CA77 in the early Harley air filter.
Transcript: http://www.open-sport.org/Repair/Keihin-carb-repair-1/
Comment at:
http://xlforum.net/vbportal/forums/showthread.php?p=5632791
Help a brother out, some Amazon associate links that pay a percentage of anything you buy during the same browser session.
A rebuild kit with Viton needle:
http://www.amazon.com/exec/obidos/ASIN/B009CA2SEU/cookinexperi-20
Rebuild kit just for accel pump:
http://www.amazon.com/exec/obidos/ASIN/B00HXJAP2O/cookinexperi-20
the Viton O-ring:
http://www.amazon.com/exec/obidos/ASIN//cookinexperi-20
Clamps and O-rings:
http://www.amazon.com/exec/obidos/ASIN/B009BQXBH8/cookinexperi-20
Видео Keihin butterfly carb rebuild #1 канала Open-Sport.org
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Keihin butterfly carb rebuild #2Keihin butterfly carb rebuild #3Keihin butterfly carb rebuild #404 How to inspect and adjust float level on a carburetor. BONUS: RICH LEAN Fuel Settings explained!Harley Davidson Shovelhead Points Installation and TimingSportster carburetor rebuild complete guideKohler carb rebuildWHY your motorcycle only runs on CHOKEKeihin and Mikuni Butterfly Carb Tuning TipsDon't rebuild your carburetor try this first!Harley Sportster 1000 carb installS&S Cycle - Super E & G Carburetor - Basic SetupCarburetor Float Height Measurement & Adjustment- Keihin PWK 38 Air Striker Short with STICSnowmobile carburetor explainer. Adjustments and cleaning. The most important parts!Rejetting the Carburetor on a Harley Twin CamAvoid this Edelbrock Carburetor Tuning Mistake !!!!The Simplest Carburetor Known To Mankind! EP 61How To, Harley Davidson Accelerator Pump Rebuild.How to assemble a FCR KEIHIN carb from bare carb body01 "How to" CV Carburetor : Disassembly Recording Jets and Settings Cleaning Carb Rebuild Series