HOW TO BUILD A SHED
This is part 3 of a 5 part video series on building a shed. In this episode I cover building and installing the rafters, installing the perlins, and I frame up the end-wall.
This shed was built in spring of 2019 and the total cost of materials was $3500
Here is the materials list.
Part 1
10- 4X8X16 concrete blocks (pads)
12- 2x6x12' treated (for runners/beams)
24- 2x4x12' treated (floor joist and girth boards)
8 pcs 4'x8'x3/4" ADVANTECH subfloor (available at lowes)
5 lbs 3" deck screws
5 lbs 2" deck screws
Part 2
14- 2x4x12 ’ regular (Top & bottom plates + perlins)
16- 2X4X10’ regular (Top & bottom plates + perlins)
42- 2x4x8’ regular (Studs + bracing)
2- 4x4x8’ Cedar-tone treated (porch header / loft floor) (Available at Menards)
3- 2x8x12’ Cedar-tone treated (porch header / loft floor) (Available at Menards)
1-2x8x8’ Cedar-tone treated (porch header / loft floor) (Available at Menards)
10 lbs 16 penny nails
2 lbs 3” deck screws
Part 3
26-2X4X8' (rafters)
2 pcs 4x8x7/16" O.S.B. (rafter plates)
6 - 2X4X12' (spacer perlins)
11-2x4x16' (roof perlins)
1 - 2x4x12' (roof brace)
5 - 2x4x10' (end-wall framing)
3 - 2x4x8' (end-wall framing
1 - 2x4x12' (end-wall perlins)
1 - 2x4x10' (end-wall perlins)
4 - 2x4x8' (end-wall perlins)
5 lbs 16 penny nails (framing)
3 lbs 8 penny nails (rafter plates)
Part 4
Roof and trim = (CHARCOAL Color)(crinkle texture)
16 pcs metal 66” (upper part of roof)
16 pcs metal 30” (lower part of roof)
4- 8’x3 ½” corners (Shed wall corners)
4-10’x3 ½” corners (ends of the roof)
6 pcs rat guard (bottom of sidewall metal)
8 pcs j-channel (around the doors)
5 pcs drip edge 4”x4” (bent for a 24/12 pitch) (roof eave)
5 pcs break trim 4”x4” (bent for a 10/12 pitch) (break between upper and lower roof)
3 pcs ridge cap (peak of roof)
1 bag of 2” Charcoal screws (250) (to fasten the roof metal)
1 bag of 1” Charcoal screws (250) (to fasten corners)
32 solid foam closures (under break trim and ridge cap)
1 – 4’x125’ roll of bubble-wrap (roofing underlayment)
Sidewall metal = (IVORY color)
2 pcs metal 120” (each side of garage door)
3 pcs metal 85” (each side of entry door)
14 pcs metal 83” (both sidewalls)
4 pcs metal 54” (2 center pieces on each gable end)
2 pcs metal 3’ (2 outer pieces on gable above porch)
2 bags 1” Ivory screws (500) (sidewall metal)
Garage door trim = white
1 pc 1 ½”x7”x10’ (hemmed on both sides) (bottom piece)
3 pcs 1 ½”x 4 ½”x10’ (sides and top pieces)
1 lb 1 ½” roofing nails (to nail trim on)
1 lb 1” white stainless steel trim nails (to nail garage door trim and seals)
Part 5
Deck
9 - 5 1/2 X 10’ treated decking
2lbs 2 1/2” deck screws
Loft
9- 5 1/2” X 10’ treated decking
Or 1 1/2 pcs 4’ X 8’ Advantech
2lbs 2 1/2” deck screws
8’ wide X 7’ tall Garage Door
2-7’ garage door seals
1-8’ garage door seal
Garage door latch
1-36” Entry door (left hand)
Doorknob/deadbolt combo
Pack of shims
2- 24” wide X 36” tall windows
1-18” wide X 24” tall (loft) window
1 lb 1 1/2 roofing nails
Secondary loft (light weight storage)
7-2x6x12’. (Loft Joists)
2-2x4x8’ (cut in 12” for blocks to support 2x6)
3 pcs 7/16” osb (Loft floor)
18- 7/16” h clips
1 lb 2 1/2” screws
1 lb 1 1/4”!screws
Electrical
3 single nail on boxes
2 light boxes
1 plug-in & cover
2 3way switches & 2 single covers
2 white lamp holders & bulbs
60’ 14-3 wire
10’ 14-2
Wire staples
MATERIAL LIST IS NOT GUARANTEED
FOR ENTERTAINMENT PURPOSES ONLY
Видео HOW TO BUILD A SHED канала M.T. HOMES
This shed was built in spring of 2019 and the total cost of materials was $3500
Here is the materials list.
Part 1
10- 4X8X16 concrete blocks (pads)
12- 2x6x12' treated (for runners/beams)
24- 2x4x12' treated (floor joist and girth boards)
8 pcs 4'x8'x3/4" ADVANTECH subfloor (available at lowes)
5 lbs 3" deck screws
5 lbs 2" deck screws
Part 2
14- 2x4x12 ’ regular (Top & bottom plates + perlins)
16- 2X4X10’ regular (Top & bottom plates + perlins)
42- 2x4x8’ regular (Studs + bracing)
2- 4x4x8’ Cedar-tone treated (porch header / loft floor) (Available at Menards)
3- 2x8x12’ Cedar-tone treated (porch header / loft floor) (Available at Menards)
1-2x8x8’ Cedar-tone treated (porch header / loft floor) (Available at Menards)
10 lbs 16 penny nails
2 lbs 3” deck screws
Part 3
26-2X4X8' (rafters)
2 pcs 4x8x7/16" O.S.B. (rafter plates)
6 - 2X4X12' (spacer perlins)
11-2x4x16' (roof perlins)
1 - 2x4x12' (roof brace)
5 - 2x4x10' (end-wall framing)
3 - 2x4x8' (end-wall framing
1 - 2x4x12' (end-wall perlins)
1 - 2x4x10' (end-wall perlins)
4 - 2x4x8' (end-wall perlins)
5 lbs 16 penny nails (framing)
3 lbs 8 penny nails (rafter plates)
Part 4
Roof and trim = (CHARCOAL Color)(crinkle texture)
16 pcs metal 66” (upper part of roof)
16 pcs metal 30” (lower part of roof)
4- 8’x3 ½” corners (Shed wall corners)
4-10’x3 ½” corners (ends of the roof)
6 pcs rat guard (bottom of sidewall metal)
8 pcs j-channel (around the doors)
5 pcs drip edge 4”x4” (bent for a 24/12 pitch) (roof eave)
5 pcs break trim 4”x4” (bent for a 10/12 pitch) (break between upper and lower roof)
3 pcs ridge cap (peak of roof)
1 bag of 2” Charcoal screws (250) (to fasten the roof metal)
1 bag of 1” Charcoal screws (250) (to fasten corners)
32 solid foam closures (under break trim and ridge cap)
1 – 4’x125’ roll of bubble-wrap (roofing underlayment)
Sidewall metal = (IVORY color)
2 pcs metal 120” (each side of garage door)
3 pcs metal 85” (each side of entry door)
14 pcs metal 83” (both sidewalls)
4 pcs metal 54” (2 center pieces on each gable end)
2 pcs metal 3’ (2 outer pieces on gable above porch)
2 bags 1” Ivory screws (500) (sidewall metal)
Garage door trim = white
1 pc 1 ½”x7”x10’ (hemmed on both sides) (bottom piece)
3 pcs 1 ½”x 4 ½”x10’ (sides and top pieces)
1 lb 1 ½” roofing nails (to nail trim on)
1 lb 1” white stainless steel trim nails (to nail garage door trim and seals)
Part 5
Deck
9 - 5 1/2 X 10’ treated decking
2lbs 2 1/2” deck screws
Loft
9- 5 1/2” X 10’ treated decking
Or 1 1/2 pcs 4’ X 8’ Advantech
2lbs 2 1/2” deck screws
8’ wide X 7’ tall Garage Door
2-7’ garage door seals
1-8’ garage door seal
Garage door latch
1-36” Entry door (left hand)
Doorknob/deadbolt combo
Pack of shims
2- 24” wide X 36” tall windows
1-18” wide X 24” tall (loft) window
1 lb 1 1/2 roofing nails
Secondary loft (light weight storage)
7-2x6x12’. (Loft Joists)
2-2x4x8’ (cut in 12” for blocks to support 2x6)
3 pcs 7/16” osb (Loft floor)
18- 7/16” h clips
1 lb 2 1/2” screws
1 lb 1 1/4”!screws
Electrical
3 single nail on boxes
2 light boxes
1 plug-in & cover
2 3way switches & 2 single covers
2 white lamp holders & bulbs
60’ 14-3 wire
10’ 14-2
Wire staples
MATERIAL LIST IS NOT GUARANTEED
FOR ENTERTAINMENT PURPOSES ONLY
Видео HOW TO BUILD A SHED канала M.T. HOMES
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
(PART 2) HOW TO INSTALL VINYL PLANK FLOORING (LVP)New Pool Liner!The Final ProductTile shower, laminate flooring, and Tiffany singingRIDING HELL'S REVENGE TRAIL IN THE GENERALTrim, countertops, and backsplashHOW TO INSTALL A SLIDING BARN DOORHAPPY NEW YEAR!HOW TO LAY CONCRETE BLOCKOPHIR PASS AND SILVERTON TO DURANGO TRAIN RIDEVARIOUS SNIPS TO USE ON METAL ROOFINGHOW FAST CAN I LAY LAMINATE FLOORING?"LITTLE PENN" FLIP (full video)SILVERTON, CO - DURANGO, CO - FOUR CORNERS TO MOAB UTAHTILE SHOWER PROJECT1000 Subscribers! Thank you!HOW TO INSTALL BASE TRIMHOW TO INSTALL DOOR TRIMMetal Roof, White Trim, & New DeckMore Cleanup & Redo The Back PorchInitial Walkthrough & Cleanup