HOW TO INSTALL a LAWN SPRINKLER PUMP and MOTOR on any type of Irrigation

We show how to replace and or install a LAWN SPRINKLER PUMP and MOTOR for an Irrigation system.
🛠️🧰👨‍🔧🔩⚡ TOOLS, PARTS & MATERIAL USED IN THIS PROJECT: 👨‍🏭⚙️🔧🧰🔦⚡
GOULDS, GT20 IRRI-Gator Self-Priming Single Phase, 2 hp: https://amzn.to/2FcUF3V
1/2" liquid tight connector 90-degree 20 pack: https://amzn.to/3hzB66X
Flexible Electrical Conduit Liquid Tight PVC Conduit Kit - 5 Coupling, 3 Elbow and 10 PCS Strap: https://amzn.to/3YWa8Nh
PVC Cement and 4-Ounce NSF Purple Primer Handy Pack, 4 oz : https://amzn.to/2MZGPIy
Hacksaw, 12-inch: https://amzn.to/2MZ87yu
“As an Amazon Associate I earn from qualifying purchases at no extra cost to you.”
How to disconnect and install a lawn sprinkler pump.
This Pump services a 3 zone system, all pvc piping. Borner residential home. At some point in the lifespan of any type of sprinkler pump, it is likely to need maintenance or repairs and Replacement, so it's helpful to know in advance how to disconnect it and install a lawn sprinkler pump. Irrigation water can come from a well, natural body of water or a cistern that collects rainwater from the roof. What these sources have in common is the requirement of a pump to pressurize the irrigation system.
1 Turn off the power supply to the pump. Most systems use a pump start relay switch wired to the irrigation controller that activates the pump each time the controller opens a valve. If this is the case, unplug the controller and the power will be disconnected to the pump. If the pump is plugged into an electrical outlet, rather than hard-wired to the circuit, simply unplug it from the outlet. In any other configuration, it is necessary to locate the circuit breaker that controls the pump and flip it to the "Off" position.
2 Unscrew and or pull the plugged type that hold each electrical wire to the terminals on the pump and remove the wires. On most pumps, the wire connections are behind a metal plate or covering that must be removed first. Typically, a couple small screws must be loosened to remove the cover.
3 For PVC connection with no couplings cut the inlet pipe with an hacksaw close ti the fitting
4 Unscrew the other fitting from the pump, which goes to the sprinklers.
5 Remove any screws or bolts that hold the pump to the floor. These pass through holes in the base of the pump, but are not always used. The pump can now be removed for repair.
The new pump we installed is GOULDS Pumps GT20 IRRI-Gator Self-Priming Single Phase Centrifugal Pump, 2 hp, Blue.
7 Things You Will Need
 Screwdriver
 Hacksaw
 Fine sandpaper: https://amzn.to/2S4AhbC
 Pvc primer
 Pvc cement or glue
 Pipe wrench or channel lock plier
 Pvc pipes and fittings depending on your system
 Waterproof marker
Tips
Warning
 If there is any doubt about whether the power supply to the pump has been disconnected successfully, contact a licensed electrician for help before disconnecting the pump and to reconnect the new one.

See HOME IMPROVEMENT Projects Playlist for more;
https://www.youtube.com/watch?v=7BzMW0DT6yc&list=PLKE7F0aRK-jnqMH0qQ0iME0_soMHS86V5

Видео HOW TO INSTALL a LAWN SPRINKLER PUMP and MOTOR on any type of Irrigation канала John C RV