Paint and Finish a V Carved Project - CNC For Beginners
Painting and Finishing a V-Carved Project
More down here ↓↓↓ Click SHOW MORE!
In this video, I’ll demonstrate how I paint and finish a v-carved project.
A lot of this goes back to standard woodworking. I use normal sanding, sealing, painting, and finishing techniques. I’ll go over it all step-by-step.
I’ll also show you how I clamp the project to my Gatton CNC and cut a horizontal keyhole slot in the back of the project.
As usual, if you have any comments or questions about anything I covered in this video, please put ‘em in the comment section below.
Link to Part 1 of this video series, Importing Files from Other Sources: https://www.youtube.com/watch?v=klTtDbcixFA
Link to the file used to make the project in this video. You must be logged into your V&Co account to download the file, but it is a FREE project: https://bit.ly/2Mj3ZtR
Thanks for watching!
For more info on a Gatton CNC kit of your own, check out Dave Gatton’s Home Page at:
http://www.davegatton.com/
Links to tools and products used in this video:
Triple Edge Finder 3-Way Touch Plate: http://www.themakersguide.com/home/products/triple-edge-finder-2
Horizontal Toggle Clamps: https://amzn.to/30Id41x
Bosch 3/8 inch Keyhole Bit: https://amzn.to/2QjGRcc
(Alternate) Whiteside 3/8 inch Keyhole Bit : https://amzn.to/2HzONDn
Duster Brush: https://amzn.to/2EwPn2P
Minwax Clear Satin Aerosol Lacquer: https://amzn.to/2MgbyRk
Sherwin Williams Paint Color Samples: https://low.es/2VHjiv3
Some links may be affiliate or sponsor links. Purchasing or even clicking through these links will help support me and the content I provide for free.
Thank you very much for your support!
Get your Official Mark Lindsay CNC T-shirts and coffee mugs here:
http://marklindsaycnc.com/index.php/product-category/logo-products/
I’m a proud founding member of the Maker’s Media Network.
Come check us out at: http://makersmedianetwork.com/
marklindsaycnc.com is sponsored by Harneal Media – a website developing company that specializes in websites for the maker community. Find out more at:
https://harnealmedia.com/
For more information on, or to download a free trial of Cut 2D, VCarve, or Aspire, visit the Vectric website at:
http://www.vectric.com/
This video is for informational and entertainment purposes only.
#VCarve #Painting #Beginner
Видео Paint and Finish a V Carved Project - CNC For Beginners канала Mark Lindsay CNC
More down here ↓↓↓ Click SHOW MORE!
In this video, I’ll demonstrate how I paint and finish a v-carved project.
A lot of this goes back to standard woodworking. I use normal sanding, sealing, painting, and finishing techniques. I’ll go over it all step-by-step.
I’ll also show you how I clamp the project to my Gatton CNC and cut a horizontal keyhole slot in the back of the project.
As usual, if you have any comments or questions about anything I covered in this video, please put ‘em in the comment section below.
Link to Part 1 of this video series, Importing Files from Other Sources: https://www.youtube.com/watch?v=klTtDbcixFA
Link to the file used to make the project in this video. You must be logged into your V&Co account to download the file, but it is a FREE project: https://bit.ly/2Mj3ZtR
Thanks for watching!
For more info on a Gatton CNC kit of your own, check out Dave Gatton’s Home Page at:
http://www.davegatton.com/
Links to tools and products used in this video:
Triple Edge Finder 3-Way Touch Plate: http://www.themakersguide.com/home/products/triple-edge-finder-2
Horizontal Toggle Clamps: https://amzn.to/30Id41x
Bosch 3/8 inch Keyhole Bit: https://amzn.to/2QjGRcc
(Alternate) Whiteside 3/8 inch Keyhole Bit : https://amzn.to/2HzONDn
Duster Brush: https://amzn.to/2EwPn2P
Minwax Clear Satin Aerosol Lacquer: https://amzn.to/2MgbyRk
Sherwin Williams Paint Color Samples: https://low.es/2VHjiv3
Some links may be affiliate or sponsor links. Purchasing or even clicking through these links will help support me and the content I provide for free.
Thank you very much for your support!
Get your Official Mark Lindsay CNC T-shirts and coffee mugs here:
http://marklindsaycnc.com/index.php/product-category/logo-products/
I’m a proud founding member of the Maker’s Media Network.
Come check us out at: http://makersmedianetwork.com/
marklindsaycnc.com is sponsored by Harneal Media – a website developing company that specializes in websites for the maker community. Find out more at:
https://harnealmedia.com/
For more information on, or to download a free trial of Cut 2D, VCarve, or Aspire, visit the Vectric website at:
http://www.vectric.com/
This video is for informational and entertainment purposes only.
#VCarve #Painting #Beginner
Видео Paint and Finish a V Carved Project - CNC For Beginners канала Mark Lindsay CNC
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
How to PAINT a Wood Sign Quick & EasyImporting CRV Files From Outside Sources - Part 22 - Vectric For Absolute BeginnersA Secure CNC Mounting Technique - NO DOUBLE SIDED TAPE!Design a V Carved Monogram in VCarve or Aspire – The Easier MethodBuilding inventory for a woodworking booth - lots of CNC projectsBasic Bitmap Trace and Node Editing - Part 14 - Vectric For Absolute BeginnersHow to Make and Finish a CNC Carved Sign - the process and execution!ENGRAVING WITH COLOR😜HOW TO COLOR FILL YOUR ENGRAVING LIKE A BOSS🐱👤Color filled plaque on CNC using OramaskHow to VCarve Extreme Detail and New Paint MethodHow to Enter and Use A Keyhole Bit in Vectric - Part 12 - Vectric For Absolute BeginnersColor Filling Techniques for engraving and carvingHow to do TEXT on TEXT using Vectric aspire. - How to Make this popular text on text sign that sellsCNC Router Projects- Start to Finish: Painting TechniqueX-CARVE Chicago Cubs with Colored Epoxy ProjectHow I Made 100 Walnut Cheese Trays With My Desktop CNC Router // Andy Bird BuildsHow to color fill laser engraved wood signHow to Paint a Sign Using Masking Film (PART 3)Color Filled CNC Plaque on the ShapeokoTapered Ball Nose Bits - Part 34 - Vectric For Absolute Beginners