How to Replace a Porch Column | Ask This Old House

In this video, general contractor Tom Silva shows a homeowner how to remove and repair the rot eating away at his porch’s support post.

SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse.

Tom Silva lends some support to a homeowner suffering under a rotted porch post. Tom and the homeowner dig into the rotten post base to find the issue, and then get to work removing the affected wood. Next, Tom shows the homeowner how to mill new components from a recycled, water-resistant material before putting everything back together for caulk and paint.

Skill: ⅗
Cost: Around $200
Time: 4 hours

Materials:
Scrap 4x4 post [https://thd.co/3LdAFOW]
Rice hull boards [https://bit.ly/3gxgYn0] (or other weather-resistant wood)
Fast-setting epoxy or polyurethane glue [https://amzn.to/3GxDCq8]
Shims [https://amzn.to/35Q4e8V]
Sandpaper [https://amzn.to/3gwRxSx]
Screws [https://thd.co/30fYbYV]
Construction adhesive [https://amzn.to/3B2BDZP]

Tools:
Bottle jack [https://amzn.to/3HzFXSx]
Reciprocating saw with a 10-inch blade [https://amzn.to/335g6mx]
Miter or circular saw [https://amzn.to/3gydzVb]
Level [https://amzn.to/3uFNXxE]
Scribes [https://amzn.to/3guQVgw]
Pencil [https://amzn.to/3owpCGU]
Bandsaw or table saw [https://amzn.to/3HC7h2u]
Brad nailer [https://amzn.to/3oshvLq]
Jigsaw [https://amzn.to/34LnpR2]
Router and bits [https://amzn.to/34FK5lm]
Sander [https://amzn.to/3GE64X7]
Drill and spade bits [https://amzn.to/3ryQdFi]
Impact driver and driver bits [https://amzn.to/3B6qJlD]
Caulk gun [https://amzn.to/3ovHYb3]

How To Repair Rotted Porch Post
1. Place the 4x4 post and bottle jack underneath a header on the porch and lift the porch roof slightly until the post is free from the ground. Remove any of the rotted material by hand, but do not reach under the post for safety’s sake.
2. Use a reciprocating saw fitted with a 10-inch wood cutting blade to remove the rot. Be sure to make this cut as level and evenly as possible.
3. Cut a piece of the rice hull board or wood to the correct square dimensions. Often, this is 2 or 3 inches wider than the post’s diameter. It might be necessary to double this block with an additional layer of wood to match the other posts. If that’s the case, glue the two blocks together with a fast-setting adhesive.
4. Place the block under the post and level it side to side and front to back with shims. Once level, place small strips of wood along the perimeter on top of the block. Use the scribes to mark the pitch of the surface on these strips. Be sure to mark each strip and its location as you go. Cut the strips along the scribe lines on a bandsaw or table saw before gluing them to the block with the adhesive.
5. Use the scribes to draw a circle of the appropriate size on a piece of the rice hull board or wood. For thicker profiles, screw two layers of the wood together before cutting along the circle with the jigsaw. Sand both layers smooth and evenly, and add a detail with a router, if desired.
6. Repeat the last step, but with a smaller circle to create a cascading profile. Drill a ¾-inch hole in the middle of each of these circles to allow for airflow and prevent future rot.
7. Assemble the pieces under the post. Before lowering the post, squeeze a bead of construction adhesive between the post and the new base.
8. Lower the jack slowly, allowing the post to settle on the base and squeeze the excess construction adhesive out. Smooth the excess adhesive before allowing it to dry.
9. At each corner, drive a screw from the top-most layer of the base into the bottom base. Fill the screw holes and paint.

Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free: https://bit.ly/2GPiYbH

Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet: https://www.thisoldhouse.com/pages/streaming-app

About Ask This Old House TV:
From the makers of This Old House, America’s first and most trusted home improvement show, Ask This Old House answers the steady stream of home improvement questions asked by viewers across the United States. Covering topics from landscaping to electrical to HVAC and plumbing to painting and more. Ask This Old House features the experts from This Old House, including general contractor Tom Silva, plumbing and heating expert Richard Trethewey, landscape contractor Jenn Nawada, master carpenter Norm Abram, and host Kevin O’Connor. Ask This Old House helps you protect and preserve your greatest investment—your home.

Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/AskTOHIG

How to Replace a Porch Column | Ask This Old House
https://www.youtube.com/user/thisoldhouse/

Видео How to Replace a Porch Column | Ask This Old House канала This Old House