How to Resurface a Cylinder Head at Home
In order for a cylinder head to work properly, it needs to have a near perfectly flat surface to seal against the head gasket. In this video, we show how we machined our cylinder head at home, with a flat surface, a piece of sandpaper and some light pressure. The result has proven to work, as the engine is still to this day operating fine.
The "proper" way to machine a cylinder head is by having a machine shop do it on a surface grinder. However, these problems often pop up when you least expect it. Maybe you need to get the car back on the road asap. Maybe you cant afford to have it done the 'proper' way. Whatever the case, this basic DIY repair job is do-able in your own home with basic tools you probably already own.
This may or may not work properly for your circumstance, depending on how bad the cylinder head is to start with, as well as the engine block surface. Many metal style gaskets will require a near mirror finish to seal, which must be achieved by a machine. However, this repair may get you out of trouble for a short time.
*dislaimer* - Only work on your own vehicle if you are allowed to in your region/country/state/town. Otherwise, make sure this job is carried out by a licenced mechanic.
Visit our online performance parts store : www.mrparts.com.au
This is a longer form clip of a full video that is available here - https://youtu.be/Vz1zP-5Q8vY
.
.
.
.
.
.
.
.
.
.
Non-copywrite free music used with permission from https://www.youtube.com/channel/UCzW9IT5ylJ87DLcorSpM2Eg
Видео How to Resurface a Cylinder Head at Home канала Broomy's Garage
The "proper" way to machine a cylinder head is by having a machine shop do it on a surface grinder. However, these problems often pop up when you least expect it. Maybe you need to get the car back on the road asap. Maybe you cant afford to have it done the 'proper' way. Whatever the case, this basic DIY repair job is do-able in your own home with basic tools you probably already own.
This may or may not work properly for your circumstance, depending on how bad the cylinder head is to start with, as well as the engine block surface. Many metal style gaskets will require a near mirror finish to seal, which must be achieved by a machine. However, this repair may get you out of trouble for a short time.
*dislaimer* - Only work on your own vehicle if you are allowed to in your region/country/state/town. Otherwise, make sure this job is carried out by a licenced mechanic.
Visit our online performance parts store : www.mrparts.com.au
This is a longer form clip of a full video that is available here - https://youtu.be/Vz1zP-5Q8vY
.
.
.
.
.
.
.
.
.
.
Non-copywrite free music used with permission from https://www.youtube.com/channel/UCzW9IT5ylJ87DLcorSpM2Eg
Видео How to Resurface a Cylinder Head at Home канала Broomy's Garage
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
How to check your Cylinder Head for Leaking Valves #diy #backyardmechanic #doityourself #carsWorld’s FASTEST Street Cars | Hot Rod Drag Week 2023 | Days 1 to 5 HighlightsHow to Test for Intake Leaks on your EngineHow to Use FuelTech ecu Software (FT450, FT550, FT550 lite, FT600)That’s how race cars work 💴 💰 💵 🏎️ #racecarRotors battling 2JZ, RB, K series and more! | Drag Racing - Jamboree 2023Time To Go Racing!….. but first, The MOON TUNERotary Engine Conspiracy Theories.... Fact or Fiction?Fastest 60ft EVER for the RX7, but then…..Satisfying Snow Foam Car Wash 🧼 @BowdensOwnMaking a Strut Brace for the Barra Swap RX4 | RX7 is RACE READY!How to Make a PORTABLE Transmission CoolerStreet Outlaws NPK Vs Australia - Calder Park, Day 1Davies Craig Water Pump Install Tip | Don’t Make This Mistake !Vanilla Rice RX7 is BACK ! Drag Racing at Heathcote Park RacewayHow to Rebuild a Mechanical Fuel Pump (Waterman, Kinsler, Enderle, Aeromotive)Drag Challenge Test Day & Our RX7 DISASTERHow To Do A Burnout…Aussie Junkyard Digging for Gold | Barra RX4 | 1973 Mazda BARRA Project Car Ep 13What Makes a Car a ‘Street Car’? | Racing | Rotaries & MoreBarra RX4 | Intercoolers, Fittings, 10,000 subs and Simmons! | 1973 Mazda BARRA Project Car Ep 12