Ford AOD, AODE, 4R70W Transmission Linkage | Curt's Corner at Monster Transmission
Monster Transmission Presents Curt's Corner as Curt goes over how to exchange the lever arms for the Detent or TV Cable Rod
This process and principle will apply for the Ford AOD Transmission, Ford AODE Transmission, or the Ford 4R70W transmission.
In order to change the linkage you'll have to change it from the inside of the pan. There are 16 different linkage arms offered for an AOD Ford Transmission. So there are a lot of variables, such as 2 wheel drive, or if it's a truck, or a Mustang, etc...
If your transmission is built by Monster Transmission we will provide the specific linkage system that you request.
To start the process you'll remove the pan, and for a little more room to work with the transmission filter as well. Then the transmission valve body is exposed and you'll be able to access your internal shift linkage system. In the linkage Monster Transmission during a rebuild will add an extra component to prevent the shaft from going behind the TV rod. Once inside you'll first remove the rooster tail which has an 8mm bolt. Then under the rod there is a 13/16" nut that you will loosen that will release the tension off of the shaft.
Then a roll pin that fits inside of the casting of the case. This prevents the rod from sliding out of the case. You can use cutting dice or needle nose pliers to remove it.
Once that pin is removed the linkage will pull out after removing that 13/16 nut that was previously loosened. Then you can slide the linkage out of the case. The new linkage will then slide over the TV shaft, and line the rooster tail up with the linkage. The 2 flat lands are equal on both sides so it could be placed up or down. Then tighten the 13/16 nut on the new shaft. Before tightening all the way, make sure the linkage is all lined up. If you miss the valve you won't have any movement at all. So make sure its lined up correctly. Make sure the valve and that the TV system is correctly attached. Then install the roll pin and tap it into place, not too far down though so you can remove at a later time if needed. Then there is a spring back behind the TV valve rod you can pull it around and rest it against a shift place on the valve body. Then reinstall the rooster tail tensioner.
Then its re-install it and test to make sure all linkage works properly.
Also verify the TV Bracket is attached correctly and springs back, then reinstall the transmission filter and filter gasket. Then last but not least the pan gasket and transmission pan.
If you still have further questions then give us a call at 800-708-0087
Check out our site http://MonsterTransmission.com
Видео Ford AOD, AODE, 4R70W Transmission Linkage | Curt's Corner at Monster Transmission канала Monster Transmission
This process and principle will apply for the Ford AOD Transmission, Ford AODE Transmission, or the Ford 4R70W transmission.
In order to change the linkage you'll have to change it from the inside of the pan. There are 16 different linkage arms offered for an AOD Ford Transmission. So there are a lot of variables, such as 2 wheel drive, or if it's a truck, or a Mustang, etc...
If your transmission is built by Monster Transmission we will provide the specific linkage system that you request.
To start the process you'll remove the pan, and for a little more room to work with the transmission filter as well. Then the transmission valve body is exposed and you'll be able to access your internal shift linkage system. In the linkage Monster Transmission during a rebuild will add an extra component to prevent the shaft from going behind the TV rod. Once inside you'll first remove the rooster tail which has an 8mm bolt. Then under the rod there is a 13/16" nut that you will loosen that will release the tension off of the shaft.
Then a roll pin that fits inside of the casting of the case. This prevents the rod from sliding out of the case. You can use cutting dice or needle nose pliers to remove it.
Once that pin is removed the linkage will pull out after removing that 13/16 nut that was previously loosened. Then you can slide the linkage out of the case. The new linkage will then slide over the TV shaft, and line the rooster tail up with the linkage. The 2 flat lands are equal on both sides so it could be placed up or down. Then tighten the 13/16 nut on the new shaft. Before tightening all the way, make sure the linkage is all lined up. If you miss the valve you won't have any movement at all. So make sure its lined up correctly. Make sure the valve and that the TV system is correctly attached. Then install the roll pin and tap it into place, not too far down though so you can remove at a later time if needed. Then there is a spring back behind the TV valve rod you can pull it around and rest it against a shift place on the valve body. Then reinstall the rooster tail tensioner.
Then its re-install it and test to make sure all linkage works properly.
Also verify the TV Bracket is attached correctly and springs back, then reinstall the transmission filter and filter gasket. Then last but not least the pan gasket and transmission pan.
If you still have further questions then give us a call at 800-708-0087
Check out our site http://MonsterTransmission.com
Видео Ford AOD, AODE, 4R70W Transmission Linkage | Curt's Corner at Monster Transmission канала Monster Transmission
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
This Makes How Much Power?!?? #viral #foryou #funny #trending #fast #toyStacey David With Gearz On SPEED Channel - Monster Transmission ViziKoat4R100 Mega Monster In A Box Rebuild Kit | Monster TransmissionTwo Guys Garage | Monster Transmission Handshake Warranty - SPEED ChannelInternational Shift Awareness Month ☮ 2016 Press ConferenceMonster Transmission's C6 SS Mega Monster In A BoxMonster Transmission's 200 4R Monster In A BoxBand Comparison | Monster TransmissionMonster Transmission Ribbon Cutting Ceremony | The Monster Tour - ViziKoat Presentation4L65E Transmission Showcase In Depth with Monster Lead Builder Nate Fuller - (Part 2 of 3)Kyle's Monster Transmission 4L65E Monster in a Box rebuild kit review4L60E SS 98-02 Mega Monster In A BoxYour wish is our command #foryoupage #fyp #automotive #cars #viral #funny #foryou #trending🚗Driving Tips with Dr.Shiftwell🚕Monster Transmission's C4 SS Monster In A Box4L60E 93-97 Mega Monster In A Box OverviewTech Tip | Trans Cooler🔧Transmission Symptoms and Diagnosis With Dr.John Shiftwell🚙Monster Transmission Video Blog 19Inside the Monster - Marketing, Time Lapses & Tech Tip Brake Drum - EP5Monster Transmission Video Blog Episode SIX