Ford Heated Windscreen Not Working Fuse Check- Quick Fixes From Home. Instructions In Description!
In this video, we take a look at repairing a ford focus quick-clear heated windscreen. I show how to check the fuses for each side of the screen and where the ribbon connectors are.
UPDATE THIS IS NOW FIXED
SEE PART 2 HERE, https://youtu.be/mwCEflRYG2w
Please say thanks in the comments..
Here's a link to the fuses. https://geni.us/6jF7sqX (paid link) As an Amazon Associate, I earn from qualifying purchases
Here's a link to the ford forum that shows how to do the repair
https://passionford.com/forum/technical-help-q-and-a/413220-how-to-fix-faulty-heated-front-windscreen.html
Here's a vid on removing the Scuttle to access the ribbon
https://youtu.be/cG7g3wR-4DM
Here's a vid showing the ribbon locations
https://youtu.be/jtDg5we3R3E
Here are the instructions for replacing the ribbon
1. Open bonnet
2. Remove rubber covers on window wipers. Expose nuts
3. Using a set of grips or spanner undo bolts
4. THE WINDOW WIPERS.
To remove the wipers, push down on the join and pull the wiper arm towards the engine bay and lift up. x2
5. You will see around about 8 clips holding on the plastic trim that the wiper supports come through. Remove these clips
6. Remove plastic trim, this just peels off.
7. Now you have exposed the window wiper bars and heating elements.
Take a look on the driver side and you will see a cable hanging loose and a black tab hanging from under your window.
8. Disconnect cable and cut open the opposite end to expose the cable inside. You will see small square of treated copper.
9 scrape off the silver to expose copper.
10. Get some 2.5mm stranded cable around 10 inches is enough. strip 10mm of insulation away and using a solder iron tin the end fully. Heat shrink can be added to this cable.
11. Tin with solder the exposed copper on the small square of copper.
12. If you can clamp these 2 cables together while you solder then do so as it can be tricky. If not get someone to help you.
13. Heat both parts together and add extra solder to join both parts. Leave to cool/set then slide black rubber over the joint and tape closed.
14. Using the same method as you have just carried out, peel back some of the black covering to expose the silver looking copper. scrape away carefully a section to expose the copper and tin with solder.
15. Strip around about 15mm off insulation from the other end of the cable and tin with solder.
16. Clamp these to sections together or get a friend to hold.
17. Apply heat from the solder iron and add extra solder to get a good connection. Leave to cool and set and then tape exposed joint.
18. Plugging the cable back in and test window to make sure it now works. This can be tested by boiling a kettle and letting it sit in your car.
19. Once you have confirmed the window heater works unplug and reroute the cable so it is kept as far away from the wiper bars as possible. Reconnect the plug.
20. It is now time to put the plastic trim back on.
TIP make sure the trim is fixed into the runner bar first before putting clips back on.
21. With the trim all secure and clips in place, rescuer the wiper blades. The same rule applies when putting back on as you did taking off. but push the wiper up the window.
22. Job Complete.
Видео Ford Heated Windscreen Not Working Fuse Check- Quick Fixes From Home. Instructions In Description! канала Stampys Random Reviews
UPDATE THIS IS NOW FIXED
SEE PART 2 HERE, https://youtu.be/mwCEflRYG2w
Please say thanks in the comments..
Here's a link to the fuses. https://geni.us/6jF7sqX (paid link) As an Amazon Associate, I earn from qualifying purchases
Here's a link to the ford forum that shows how to do the repair
https://passionford.com/forum/technical-help-q-and-a/413220-how-to-fix-faulty-heated-front-windscreen.html
Here's a vid on removing the Scuttle to access the ribbon
https://youtu.be/cG7g3wR-4DM
Here's a vid showing the ribbon locations
https://youtu.be/jtDg5we3R3E
Here are the instructions for replacing the ribbon
1. Open bonnet
2. Remove rubber covers on window wipers. Expose nuts
3. Using a set of grips or spanner undo bolts
4. THE WINDOW WIPERS.
To remove the wipers, push down on the join and pull the wiper arm towards the engine bay and lift up. x2
5. You will see around about 8 clips holding on the plastic trim that the wiper supports come through. Remove these clips
6. Remove plastic trim, this just peels off.
7. Now you have exposed the window wiper bars and heating elements.
Take a look on the driver side and you will see a cable hanging loose and a black tab hanging from under your window.
8. Disconnect cable and cut open the opposite end to expose the cable inside. You will see small square of treated copper.
9 scrape off the silver to expose copper.
10. Get some 2.5mm stranded cable around 10 inches is enough. strip 10mm of insulation away and using a solder iron tin the end fully. Heat shrink can be added to this cable.
11. Tin with solder the exposed copper on the small square of copper.
12. If you can clamp these 2 cables together while you solder then do so as it can be tricky. If not get someone to help you.
13. Heat both parts together and add extra solder to join both parts. Leave to cool/set then slide black rubber over the joint and tape closed.
14. Using the same method as you have just carried out, peel back some of the black covering to expose the silver looking copper. scrape away carefully a section to expose the copper and tin with solder.
15. Strip around about 15mm off insulation from the other end of the cable and tin with solder.
16. Clamp these to sections together or get a friend to hold.
17. Apply heat from the solder iron and add extra solder to get a good connection. Leave to cool and set and then tape exposed joint.
18. Plugging the cable back in and test window to make sure it now works. This can be tested by boiling a kettle and letting it sit in your car.
19. Once you have confirmed the window heater works unplug and reroute the cable so it is kept as far away from the wiper bars as possible. Reconnect the plug.
20. It is now time to put the plastic trim back on.
TIP make sure the trim is fixed into the runner bar first before putting clips back on.
21. With the trim all secure and clips in place, rescuer the wiper blades. The same rule applies when putting back on as you did taking off. but push the wiper up the window.
22. Job Complete.
Видео Ford Heated Windscreen Not Working Fuse Check- Quick Fixes From Home. Instructions In Description! канала Stampys Random Reviews
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Review- Tounee Book Stand for ReadingDenvix Tyre Inflator ReviewHIPA 2 Stroke Carburetor Tools ReviewHow To Back Up Windows 10 Computer PC Laptop To External Hard Drive (Without Software)P.I.T. Portable 3 Drawer Steel Tool Box with Magnetic Locking DimensionsHow To Clean A Trumpet Part 1 of 2How To Use FEELNEEDY Cat Water Fountain Pet Water Fountain ReviewReview - Gracioso Walkman Cassette Recorder Player: AM FM Compact Vintage Cassette Tape PlayerStop Bathtub Creaking And Squeaking. No NonsenseK +M Trumpet Stand How To AssembleP.I.T. Portable 3 Drawer Steel Tool Box with Magnetic Locking, Quality ReviewHow To Connect Your Phone Apps To FORD SYNCQuality Review - Stanley IceFlow Flow BottleHow To Build 4 Tier Plastic Storage Bins 23QT, Stackable Storage Containers with Wheels and LidsReview - ColdSky 𝟮𝟬𝟬𝟬𝟬𝗺𝗔𝗵 Camping Fan with 𝗗𝘂𝗮𝗹 𝗠𝗼𝘁𝗼𝗿6 PC Drill brush set reviewMercury Mariner 6hp Outboard Boat Motor ReviewDenvix Tyre Inflator IN USE ReviewStop Squeaky Floorboards. No Nonsense.Black + Decker Dust Buster In Use ReviewInside A Trumpet Valve Alignment Using An Endoscope