Make a Solar Cell - TiO2/Raspberry based
In this video we show how to make a dye sensitized solar cell based on titanium dioxide and anthocyanin found in raspberries.
First get some titanium dioxide (anatase structure), about 0.5g will do. Then mix it with drops of vinegar until it has the consistency of thin paint or liquid corrector fluid. Add a drop of dishwashing detergent. This is to make it stick to the glass.
Now get a piece of indium tin oxide glass. The indium tin oxide glass was purchased from delta technologies http://www.delta-technologies.com/
using a multimeter set to measure resistance, find the conductive side by measuring the resistance of the glass. The side that's conductive will have a much lower resistance than the non-conductive side.
Tape the glass on three sides onto a flat surface, conductive side up. there should be able 5mm of tape on each edge. The tape will serve as a spacer guide for the titanium dioxide.
Now using a glass rod, apply the titanium dioxide paint to the conductive of the indium tin oxide glass. Slide the rod across the tape so that it smears the paint evenly and smoothly across the glass. If the paint leaves streaks, you need to add more vinegar and try again. It should go on with a smooth coat.
Now let the slide dry on air. Then carefully peel off the tape and get the slide. Use a damp cloth to clean off any excess titanium dioxide that might have oozed around behind the slide or off the edges.
Place the slide, conductive side up, on a hot-plate and heat to 200+ celsius (preferably 550 celsius). The detergent and the vinegar will burn away and bake together the particles of titanium dioxide so that they stick to the glass. At first it will turn yellow and then turn light again as this happens. The whole process takes about 20 minutes.
As that happens, get some fresh raspberries (juice made from artificial flavoring cannot be used) and crush them.
Now get the cooled titanium dioxide slide and pour a few drops of the raspberry juice onto it. Be careful not to damage the titanium dioxide. Let it sit for a few minutes so the anthocyanin dyes absorb into the titanium dioxide.
Then carefully pour water and alcohol over the slide to wash away raspberry bits and other chemicals we don't need. Let the slide dry.
Take another indium tin oxide glass slide and pass the conductive side through a candle flame several times. This will build up a layer of soot that we need to catalyze the redox shuttle. Carefully wipe away the excess soot from the edges so that they match with the titanium dioxide from the slide.
Now we make the redox shuttle and electrolyte by mixing 127mg of iodine crystals with 830mg of potassium iodide and 10mL ethylene glycol. Mix thoroughly until completely dissolved.
Place a few drops of the redox shuttle and electrolyte onto the titanium dioxide and place over it the soot covered slide. The coated sides must be facing each other. Be sure to offset the slides so that you can access the conductive sides of both.
Bind the slides together using binder clips.
And that's done. the positive side is the soot covered slide, while the negative side is the titanium dioxide slide. Use alligator clips to contact the exposed sides.
The titanium dioxide (anatase type) and potassium iodide and iodine were purchased from Alfa Aesar. http://www.alfa.com
Видео Make a Solar Cell - TiO2/Raspberry based канала NurdRage
First get some titanium dioxide (anatase structure), about 0.5g will do. Then mix it with drops of vinegar until it has the consistency of thin paint or liquid corrector fluid. Add a drop of dishwashing detergent. This is to make it stick to the glass.
Now get a piece of indium tin oxide glass. The indium tin oxide glass was purchased from delta technologies http://www.delta-technologies.com/
using a multimeter set to measure resistance, find the conductive side by measuring the resistance of the glass. The side that's conductive will have a much lower resistance than the non-conductive side.
Tape the glass on three sides onto a flat surface, conductive side up. there should be able 5mm of tape on each edge. The tape will serve as a spacer guide for the titanium dioxide.
Now using a glass rod, apply the titanium dioxide paint to the conductive of the indium tin oxide glass. Slide the rod across the tape so that it smears the paint evenly and smoothly across the glass. If the paint leaves streaks, you need to add more vinegar and try again. It should go on with a smooth coat.
Now let the slide dry on air. Then carefully peel off the tape and get the slide. Use a damp cloth to clean off any excess titanium dioxide that might have oozed around behind the slide or off the edges.
Place the slide, conductive side up, on a hot-plate and heat to 200+ celsius (preferably 550 celsius). The detergent and the vinegar will burn away and bake together the particles of titanium dioxide so that they stick to the glass. At first it will turn yellow and then turn light again as this happens. The whole process takes about 20 minutes.
As that happens, get some fresh raspberries (juice made from artificial flavoring cannot be used) and crush them.
Now get the cooled titanium dioxide slide and pour a few drops of the raspberry juice onto it. Be careful not to damage the titanium dioxide. Let it sit for a few minutes so the anthocyanin dyes absorb into the titanium dioxide.
Then carefully pour water and alcohol over the slide to wash away raspberry bits and other chemicals we don't need. Let the slide dry.
Take another indium tin oxide glass slide and pass the conductive side through a candle flame several times. This will build up a layer of soot that we need to catalyze the redox shuttle. Carefully wipe away the excess soot from the edges so that they match with the titanium dioxide from the slide.
Now we make the redox shuttle and electrolyte by mixing 127mg of iodine crystals with 830mg of potassium iodide and 10mL ethylene glycol. Mix thoroughly until completely dissolved.
Place a few drops of the redox shuttle and electrolyte onto the titanium dioxide and place over it the soot covered slide. The coated sides must be facing each other. Be sure to offset the slides so that you can access the conductive sides of both.
Bind the slides together using binder clips.
And that's done. the positive side is the soot covered slide, while the negative side is the titanium dioxide slide. Use alligator clips to contact the exposed sides.
The titanium dioxide (anatase type) and potassium iodide and iodine were purchased from Alfa Aesar. http://www.alfa.com
Видео Make a Solar Cell - TiO2/Raspberry based канала NurdRage
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Make Luminol - The Complete GuideHow do Solar cells work?DSSCMake a Tritium Nuclear Battery or Radioisotope Photovoltaic GeneratorManufacturing PowerFilm Solar PanelsQuantum Dot Solar Cells. The Next Big Thing in PhotovoltaicsMaking a BATTERY From ALUMINIUM FOIL!Get Lithium Metal From an Energizer BatteryA Solar Cell From A Broken LCD Screen - Part 1 - Reclaiming The MaterialsA Simple Homemade Solar CellTitanium Dioxide Raspberry Solar CellHow to Make Solar Panels Yourself with Epoxy Glue100W Solar panel || DIY or BuyMake Potassium Chlorate by Electrolysis - The Basic GuideMake Nitric Acid - The Complete GuideWhat you need to know about printing Solar CellsMake a Zinc Air BatteryHow do SSDs Work? | How does your Smartphone store data? | Insanely Complex Nanoscopic Structures!Fabrication of a Dye-Sensitized Solar CellConstructing a Dye Sensitized Solar Cell