(3/3) Making a Tailstock Hex Die Holder Thumbscrew Set Screw from Brass for the Mini Metal Lathe
This video is how to make an indented thumbscrew without the use of a mill or a indexing chuck/fixture on the MINI LATHE. (MUCH) More information below!
Please like and subscribe if this was helpful!
Stuff from this video:
LED Shop Lights: http://amzn.to/2zPtSoF
CA Glue: http://amzn.to/2Dz46aq
Tap and Die Set: http://amzn.to/2pBk6SB
End Mill Bits: http://amzn.to/2nqbt11
Polish: http://amzn.to/2rYy7NT
Part 1: https://youtu.be/LZFSyeIDOzs
Part 2: https://youtu.be/0v06IauXoRY
Lathe: https://amzn.to/2nVBrEc
Flute Quartet: https://www.youtube.com/watch?v=DMpr_B6qqhs
Stuff on the lathe:
Quick Change Tool Holder: https://amzn.to/2oZtFee
Tailstock Drill Chuck: https://amzn.to/2pmE0jX
Dead Center: http://amzn.to/2BlFdyy
Live Center: http://amzn.to/2qhMRqH
Lathe tools:
Boring Bar: https://amzn.to/2pmy0b1
Carbide Tools: https://amzn.to/2oRZWax
Parting Tool: https://amzn.to/2nVCeW1
Center Bits: https://amzn.to/2oRRV5n
Drill Bits: http://amzn.to/2oz9W76
Other stuff:
Cutting oil: http://amzn.to/2ofkPaY
Dial Indicator: http://amzn.to/2Dzp0aa
Mini Lathe troubleshooting guide: http://littlemachineshop.com/reference/drivetroubleshooting.pdf
Controller board wiring configuration: http://imgur.com/KIEzu92
The real version of the motor controller: https://amzn.to/2orw43F
Datasheet for the KBIC-120: https://www.galco.com/buy/KB-Electronics/KBiC-120
Super nice guy who repairs the controller boards: http://olduhfguy.com/
Видео (3/3) Making a Tailstock Hex Die Holder Thumbscrew Set Screw from Brass for the Mini Metal Lathe канала TimNummy
Please like and subscribe if this was helpful!
Stuff from this video:
LED Shop Lights: http://amzn.to/2zPtSoF
CA Glue: http://amzn.to/2Dz46aq
Tap and Die Set: http://amzn.to/2pBk6SB
End Mill Bits: http://amzn.to/2nqbt11
Polish: http://amzn.to/2rYy7NT
Part 1: https://youtu.be/LZFSyeIDOzs
Part 2: https://youtu.be/0v06IauXoRY
Lathe: https://amzn.to/2nVBrEc
Flute Quartet: https://www.youtube.com/watch?v=DMpr_B6qqhs
Stuff on the lathe:
Quick Change Tool Holder: https://amzn.to/2oZtFee
Tailstock Drill Chuck: https://amzn.to/2pmE0jX
Dead Center: http://amzn.to/2BlFdyy
Live Center: http://amzn.to/2qhMRqH
Lathe tools:
Boring Bar: https://amzn.to/2pmy0b1
Carbide Tools: https://amzn.to/2oRZWax
Parting Tool: https://amzn.to/2nVCeW1
Center Bits: https://amzn.to/2oRRV5n
Drill Bits: http://amzn.to/2oz9W76
Other stuff:
Cutting oil: http://amzn.to/2ofkPaY
Dial Indicator: http://amzn.to/2Dzp0aa
Mini Lathe troubleshooting guide: http://littlemachineshop.com/reference/drivetroubleshooting.pdf
Controller board wiring configuration: http://imgur.com/KIEzu92
The real version of the motor controller: https://amzn.to/2orw43F
Datasheet for the KBIC-120: https://www.galco.com/buy/KB-Electronics/KBiC-120
Super nice guy who repairs the controller boards: http://olduhfguy.com/
Видео (3/3) Making a Tailstock Hex Die Holder Thumbscrew Set Screw from Brass for the Mini Metal Lathe канала TimNummy
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Milling a Metal ScriberMaking a Mini Lathe Carriage Lock out of a brass block to improve facing cutsLathe Die Holder (Hex Dies)60s Tutorial - Easiest Angle Setup Ever? Turning an MT2 Morse Taper on Mini Lathe, No MeasuringEverything You Need to Know About Taps & Dies - Gear Up With Gregg'sMaking Thumbscrews: Interrupted cutting and threading on the mini latheCutting Gear Teeth On The LatheУвеличиваем жесткость Тайваньского станкаMaking a Big Bolt and Nut on the LatheA simple machinist trick that often comes in handyTerry's Tips - Customise your new bench pegTilting Angle Plate /Adustable angle plateTailstock Die (and tap) HolderThe Infamous Mini Lathe!HOW TO CUT STRAIGHT AN EXTERNAL THREAD!!Making Custom Brass ThumbscrewsMaking Tailstock Hex Die Holder MT2 !!Mini Lathe - How I Made Money with a Mini Lathe and YOU can too!Expanding Mandrels for workholding on a lathe (& other ops.) #SHOPMADETOOLS