Mazdaspeed 3 - VVT & Timing Chain Replacement
We take on the infamous VVT job on the MZR 2.3 disi engine in the Mazdaspeed 3. Although we had done the job in the past, we forgot to SET CHAIN TENSION, so we did the job again to make sure we are ready to turn up the boost with the new big turbo.
*** DISCLAIMER: This video is intended for entertainment purposes only. We are not responsible for any damages that may be caused by following the steps in this video:)
Tips:
- Set the engine at TDC before removing timing components, to avoid piston to valve interference.
- Remove timing tools when loosening and tightening components, to prevent damage to timing tools, cams and block.
- When locking the cams, make sure the intake and exhaust cam lobes for cylinder 1 are facing each other at a 45 degree angle (this indicates TDC).
- Replace the crank pulley bolt as it it a stretch bolt (replacing the cam sprocket bolts is also recommended).
- Replace all friction washers, including the ones for the cam sprockets to ensure engine stays in time.
Since we already had the JBR 88A rear motor mount installed, we went ahead and installed the JBR 80A passenger, and 88A transmission motor mounts when putting it back together.
*** Check out our other videos, and be sure to SUBSCRIBE and hit the NOTIFICATION BELL to know when we upload new videos!
*** Follow us on INSTAGRAM @wannabe_tuners for more frequent updates!
*** Check out our MERCH STORE here:
https://teespring.com/stores/wannabetuners
As always, THANKS FOR TUNING!
Mods in this video:
1. Snow Performance Stage 1 WMI Kit
2. Cobb Accessport V2 (self tuned)
3. Bfg Sport Comp 2 All Seasons
4. Jbr Oil Catch Can (vta setup)
5. Ngk One Step Colder Plugs
6. Cpe Top Mount Intercooler
7. Jbr 88a Rear Motor Mount
8. Jbr 88a Trans Motor Mount
9. Jbr 80a Pass Motor Mount
10. Autotech HPFP Internals
11. Eibach Lowering Springs
12. Cnt Catted Downpipe
13. Koni Yellow Shocks
14. Volk TE37 Replicas
15. Raceland E-Cutout
16. Cobb 3 Port Ebcs
17. Resonator Delete
18. Htp Full 3" Intake
19. Bnr S4 V2 Turbo
20. Forge Bpv V1
Видео Mazdaspeed 3 - VVT & Timing Chain Replacement канала Wannabe Tuners
*** DISCLAIMER: This video is intended for entertainment purposes only. We are not responsible for any damages that may be caused by following the steps in this video:)
Tips:
- Set the engine at TDC before removing timing components, to avoid piston to valve interference.
- Remove timing tools when loosening and tightening components, to prevent damage to timing tools, cams and block.
- When locking the cams, make sure the intake and exhaust cam lobes for cylinder 1 are facing each other at a 45 degree angle (this indicates TDC).
- Replace the crank pulley bolt as it it a stretch bolt (replacing the cam sprocket bolts is also recommended).
- Replace all friction washers, including the ones for the cam sprockets to ensure engine stays in time.
Since we already had the JBR 88A rear motor mount installed, we went ahead and installed the JBR 80A passenger, and 88A transmission motor mounts when putting it back together.
*** Check out our other videos, and be sure to SUBSCRIBE and hit the NOTIFICATION BELL to know when we upload new videos!
*** Follow us on INSTAGRAM @wannabe_tuners for more frequent updates!
*** Check out our MERCH STORE here:
https://teespring.com/stores/wannabetuners
As always, THANKS FOR TUNING!
Mods in this video:
1. Snow Performance Stage 1 WMI Kit
2. Cobb Accessport V2 (self tuned)
3. Bfg Sport Comp 2 All Seasons
4. Jbr Oil Catch Can (vta setup)
5. Ngk One Step Colder Plugs
6. Cpe Top Mount Intercooler
7. Jbr 88a Rear Motor Mount
8. Jbr 88a Trans Motor Mount
9. Jbr 80a Pass Motor Mount
10. Autotech HPFP Internals
11. Eibach Lowering Springs
12. Cnt Catted Downpipe
13. Koni Yellow Shocks
14. Volk TE37 Replicas
15. Raceland E-Cutout
16. Cobb 3 Port Ebcs
17. Resonator Delete
18. Htp Full 3" Intake
19. Bnr S4 V2 Turbo
20. Forge Bpv V1
Видео Mazdaspeed 3 - VVT & Timing Chain Replacement канала Wannabe Tuners
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
MazdaSpeed 3-6 Timing Chain VVT How to change DIY ! Trouble shooting low comp DISI motorMAZDA NOT STARTING OR RUNNING GOOD AFTER CRANKSHAFT POSITION SENSOR REPLACEMENTMazdaspeed 3 - Built Engine AssemblySincronizacion tiempo mazda 6 5 3 cx7 ford ranger focus ecosport mondeo smax volvo mustangsegunda parte sincronizacion damper: mazda 6 3 ford focus ranger ecosport mondeo smax rx8 volvoMazda 2.3L TurboTiming The Mazda/Ford 2.0/2.3/2.5 Engines. Part 3 - Tools, Components, Etc,.Mazda 3 MPS - Timing Chain Tips and Tricks2004 Mazda 3 2.3 l engine cylinder head gasket removalMazdaspeed 3 - Blown Engine TeardownTiming My Built Mazdaspeed Motor!Mazdaspeed 3 Engine Build - Start To Finish2005 Mazda 3 - 2.3L to 2.5L Engine Swap. Timing Fix!2010 Mazda CX-7 Timing Chain ReplacementHow to align valve timing on 2010- 2013 Mazda 3 / Ford 2.0 engineMazda Skyactiv Engine Timing Chain ReplacementMazda CX-7 Timing chain replacement and turbo rebuild part 2 - Timing chain installationMazdaspeed - Everything You Need to Know | Up to SpeedTIMING CHAIN REPLACEMENT MAZDA 2.3 CX-7 CX7 MAZDASPEED 3 MAZDASPEED 6Timing The Mazda/Ford 2.0/2.3/2.5 Engines. Part 2 - What Can Go Wrong