RV-10 Wings - 065 - Flaps day 3! ... subassemblies, poprivets, and final assembly.
Patreon Campaign: https://www.patreon.com/palamedes
Builder ID Number: 41638
This video was posted yesterday.. No really.. it's not late.. Honest! *whistles innocently* (Life sucks sometimes..)
In this video I continue working on the left flap. I start out by dimpling everything with the pneumatic squeezer where I can. Some of it must be done with a hand held dimpler though just due to the size of the tool versus the part.
Once that's done then I go on to dimple all the skins. After that's done I assemble the subassemblies on the bottom part of the flap. I also talk to the 4 holes in the various flap hinge bracket subassemblies that I upsized based on another persons suggestion.
After I get everything dimpled and the subassemblies together, I begin the final assembly. I had to cleco the whole thing to the table to get it usable. The squeezer was painful to use due to the size of the parts so I ended up using the bucking bar/rivet gun. Worked great.
I also do a small experiment around the trailing edge of the forward rounded skins where you're supposed to add a small bend. Found something interesting.. (And no I didn't screw everything up!)
I also talk to the poprivets that go on the front and repeatedly call them the wrong things! MK-319-BS.
I also lost some video overlay at the end of this video so I talk over it a bit.. sorry about that.
Видео RV-10 Wings - 065 - Flaps day 3! ... subassemblies, poprivets, and final assembly. канала Jason Ellis Builds
Builder ID Number: 41638
This video was posted yesterday.. No really.. it's not late.. Honest! *whistles innocently* (Life sucks sometimes..)
In this video I continue working on the left flap. I start out by dimpling everything with the pneumatic squeezer where I can. Some of it must be done with a hand held dimpler though just due to the size of the tool versus the part.
Once that's done then I go on to dimple all the skins. After that's done I assemble the subassemblies on the bottom part of the flap. I also talk to the 4 holes in the various flap hinge bracket subassemblies that I upsized based on another persons suggestion.
After I get everything dimpled and the subassemblies together, I begin the final assembly. I had to cleco the whole thing to the table to get it usable. The squeezer was painful to use due to the size of the parts so I ended up using the bucking bar/rivet gun. Worked great.
I also do a small experiment around the trailing edge of the forward rounded skins where you're supposed to add a small bend. Found something interesting.. (And no I didn't screw everything up!)
I also talk to the poprivets that go on the front and repeatedly call them the wrong things! MK-319-BS.
I also lost some video overlay at the end of this video so I talk over it a bit.. sorry about that.
Видео RV-10 Wings - 065 - Flaps day 3! ... subassemblies, poprivets, and final assembly. канала Jason Ellis Builds
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
RV-10 Wings - 032 - Aileron work - lap joints and edge breaksRV-10 Wings - 005 - Left spar mistake and tie down bracketRV 10 Empennage section 10 16Aveo Engineering ZipTips - 01 - The great unboxing!RV-10 Empennage Section 6-4 steps 5 to 7RV-10 Empennage Section 7-4 Steps 1, 2 & 3RV-10 Empennage - InventoryRV-10 Wings - 006 - Left Wing Spar and an OuchieRV-10 Empennage - Workspace OrganizationRV-10 Empennage section 9-2 to 9-6Learning to Fly - 012 - Power on stall refresher and more landingsLearning to Fly - 020 - Very Gusty DayRV-10 Empennage sections 10-20 to 10-21RV-10 Empennage Section 9-14RV-10 Wings - 010 - Left wing rear spar finalizing and jstiffenersRV-10 Empennage -- VS fairing resultsRV-10 Wings - 001 - Delivery and beginning the inventoryRV-10 Empennage Section 12-2RV-10 Wings - 056 - Proseal tank jstiffener, end rib, and prepare for closing tanksRV-10 Empennage Sections 8-9 steps 5 to 7