How-To Change Engine Oil & Oil Filter in Ktm 530

See tools, tips, time, parts, and of course step-by-step how to change the engine oil and the engine oil filter in your ktm four stroke dirt bike. In this video see every step of the procedure I use to change the engine oil in my Ktm 530 as it is described in the owners manual. I'm sure there will be some carry over for other ktm 4 strokes like the sx-f 250's and sx-f 450s, so please comment below if changing the engine oil in your ktm is the same or not.

0:17 Pause Here for Tools Required (or see below)
0:21 Pause Here for Parts Required (or see below)
0:24 Pause Here for Job Overview (or see below)
0:30 Warm Up Bike on Level Surface, Grab Drain Bucket, Remove Skid Plate
0:47 Locate Correct Engine Oil Drain Plug/Screen (left one for my bike) and Remove to Drain Engine Oil
1:31 Re-install Clean Drain Plug (Torque Specs 20nm or 14.8 Ft. Lbs.)
1:55 Locate and Remove Oil Filter Cover (Two Torx 30 Star Bolts or 8mm)
2:17 Remove Oil Filter with Needle Nose Pliers
2:43 Lay Bike Down Onto Passenger Side
3:16 Fill Cavity 1/3rd Way, Fill New Filter W Oil, and Reinstall
3:44 Re-Install Oil Filter Cover (Torque Specs 10nm Or 7.4 Ft. Lbs.)
4:21 Add Remaining 550ml of Oil to Get Total Capacity right at 600Ml
5:01 Spray Oil Filter and Drain Plug Areas W/ Degreaser Hose off the Mess
5:15 Start Bike Briefly, Check For Leaks, Kill it, Check Oil Level Still Cold

Parts Required:
Correct Oil for Your Transmission
KTM Recommends Motorex 4t Sae 10w50 https://amzn.to/2LiXpQ1
I Used Mobil 1's Full Synthetic Racing 4t 10w-40 https://amzn.to/2xEWaaq
Engine Degreaser https://amzn.to/3dkDlIP
Parts Cleaner https://amzn.to/2W7W8kT
2 Beers

Tools Required:
-8mm Socket -Cheap Mechanic Socket Set- https://amzn.to/3cflFy8
-13mm Wrench -Cheap Mechanic Metric Wrench Set- https://amzn.to/3dkEi3R
-Torx T-30 Star Bit -Torx Socket Set I Use- https://amzn.to/2SKabep
-Funnel, Drain Bucket, Shop Towels, Gloves, Needle Nose Pliers
-Torque Wrench https://amzn.to/2SHzvSc
-Owners Manual https://www.ktm.com/us/service/manuals/
Job Overview:
Difficulty: Easy/Med
Time Required: 3 Beers (40-60 Mins)
Maintenance Interval: Every 15 Engine Hours
Engine Oil Capacity: 600 Ml
Level of Importance: High

Torque Specs:
Drain Plug: 20 Newton Meters (14.8 Ft. Lbs)
Oil Filter Cover Bolts: 10 Newton Meters (7.4 Ft. Lbs)
So I really hope you found some of this information helpful, when it comes time to change the oil in your KTM dirt bike, and if you did find it helpful, do me a quick favor and give the video a thumbs up.

And as always, if I missed anything, or you have any thoughts or suggestions on how to improve these videos, or really any comments on this ktm maintenance topic in general, please leave a comment in the section below, I'd love to hear from you.

I'd also really like to take a minute and thank the 1433 of you guys who have found some of the how-to content on this channel and decided to subscribe, and for those of ya'll who are following along those were beers #144-146 on my way to finishing the Escape Power Sports 1000 Beer Challenge.

So if your new to the channel I'd encourage you to SUBSCRIBE so you don't miss out on any of the rest of the dirt bike maintenance video's we will be putting out, over the course of those 1000 beers.

I'm Danny with Escape Power Sports, I really want to thank ya'll for watching/reading and until next time, We'll see ya'll on the trails.

Видео How-To Change Engine Oil & Oil Filter in Ktm 530 канала Escape PowerSports