Homemade via ferrata fall Shock Absorption System with Kong Kisa plate dissipator
Homemade via Ferrata fall Shock Absorption System with Kong Kisa plate. The video focuses on the creation of a via Ferrata kit similar to those produced in the series. The rope in the video is not the one that will be used. The rope used will have a diameter of 10.5mm or 11mm. The rubber bands that close the plastic bag will be replaced by 2 turns of adhesive tape.
2 Orange Ferrata carabiners (For the nodes, watch the video link in the description: https://youtu.be/vNrmHFddA_E ) 33Kn - 12Kn.
The green carabiner will be connected directly to the Kong Kisa shock absorber (6 holes) through a small hole in the plastic bag and will hook onto the climbing harness. Despite being metal to metal, as the harness is mobile there will be no stress exceeding 12Kn.
The termination of the Shock Absorber Kong Kisa must have at least 1.5m of free rope. Kong recommends tying a knot at the end so that the rope does not come out when it reaches the extreme tip in case of a very violent fall. For safety, I recommend attaching it to another carabiner (the blue carabiner) which will be connected to the harness service ring.
Sistema di Assorbimento Shock da caduta in via ferrata fatto in casa con piastra Kong Kisa. Il video si focalizza sulla creazione di un kit da ferrata simile a quelli prodotti in serie. La corda nel video non è quella che verrà utilizzata. La corda utilizzata avrà un diametro di 10.5mm o 11mm. Gli elastici che chiudono la borsa di plastica saranno sostituiti da 2 giri di nastro adesivo.
2 Moschettoni arancioni da Ferrata (Per i nodi guardate il link del video in descrizione) 33Kn - 12Kn.
Il moschettone verde sarà collegato direttamente allo shock absorber Kong Kisa (6 fori) attraverso un piccolo buco nella busta di plastica e si aggancerà all'imbracatura da arrampicata. Nonostante sia metallo con metallo, poichè l'imbracatura è mobile non ci saranno sollecitazioni superiori a 12Kn.
La terminazione dello Shock Absorber Kong Kisa dovrà avere almeno 1,5m di corda libera. Kong consiglia di fare un nodo all'estremità in modo che la corda non esca al raggiungimento della punta estrema in caso di caduta molto violenta. Io per sicurezza consiglio di agganciarla ad un altro moschettone (il moschettone blu) che sarà collegato all'anello di servizio dell'imbracatura.
#climbing #shockabsorber #kongkisa #climbingdissipator #dissipatorecaduta #dissipatore #hommade #kitviaferrata #setviaferrata
Видео Homemade via ferrata fall Shock Absorption System with Kong Kisa plate dissipator канала Giorgio House
2 Orange Ferrata carabiners (For the nodes, watch the video link in the description: https://youtu.be/vNrmHFddA_E ) 33Kn - 12Kn.
The green carabiner will be connected directly to the Kong Kisa shock absorber (6 holes) through a small hole in the plastic bag and will hook onto the climbing harness. Despite being metal to metal, as the harness is mobile there will be no stress exceeding 12Kn.
The termination of the Shock Absorber Kong Kisa must have at least 1.5m of free rope. Kong recommends tying a knot at the end so that the rope does not come out when it reaches the extreme tip in case of a very violent fall. For safety, I recommend attaching it to another carabiner (the blue carabiner) which will be connected to the harness service ring.
Sistema di Assorbimento Shock da caduta in via ferrata fatto in casa con piastra Kong Kisa. Il video si focalizza sulla creazione di un kit da ferrata simile a quelli prodotti in serie. La corda nel video non è quella che verrà utilizzata. La corda utilizzata avrà un diametro di 10.5mm o 11mm. Gli elastici che chiudono la borsa di plastica saranno sostituiti da 2 giri di nastro adesivo.
2 Moschettoni arancioni da Ferrata (Per i nodi guardate il link del video in descrizione) 33Kn - 12Kn.
Il moschettone verde sarà collegato direttamente allo shock absorber Kong Kisa (6 fori) attraverso un piccolo buco nella busta di plastica e si aggancerà all'imbracatura da arrampicata. Nonostante sia metallo con metallo, poichè l'imbracatura è mobile non ci saranno sollecitazioni superiori a 12Kn.
La terminazione dello Shock Absorber Kong Kisa dovrà avere almeno 1,5m di corda libera. Kong consiglia di fare un nodo all'estremità in modo che la corda non esca al raggiungimento della punta estrema in caso di caduta molto violenta. Io per sicurezza consiglio di agganciarla ad un altro moschettone (il moschettone blu) che sarà collegato all'anello di servizio dell'imbracatura.
#climbing #shockabsorber #kongkisa #climbingdissipator #dissipatorecaduta #dissipatore #hommade #kitviaferrata #setviaferrata
Видео Homemade via ferrata fall Shock Absorption System with Kong Kisa plate dissipator канала Giorgio House
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
How to Tie a Crab Claw Via Ferrata Lanyard - ITS Knot of the Week HDKong KISAKong Back-UpSlings vs Lanyards vs Personal Anchors - Differences, Usages & Safety Musts | Ep.3Prusik with tending pulley | Arborist climbing techniques10种生活中很实用的绳结,看似简单,学会了用处非常大Climbing 700 m Above The Abyss: Stairway To Heaven In Austria | Axel On The EdgeEDELRID Knowledge Base - In-depth knowledge about via ferrata setsCose da climber: Come costruire un rinvio allungabileBest Knots for Climbing—The 5 Knots Every Climber Should Know || REIEDELRID – VIA FERRATA (EN)Via Ferrata Dolomites: practical handbook and technical manualCome Costruire un kit per Via Ferrata con Dissipatore di Caduta - frizione (tutorial)Kong Gigi ReviewLonża Arborystyczna DIYSwitzerland's longest Via Ferrata - Solo ClimbBreak Testing Knots - Zeppelin & Figure 8 & Alpine Butterfly & Reever & Bowline & Double Fisherman#08 - Need a REST on Via Ferrata? | Via Ferrata tutorial for Beginners | Practical TipsУзлы для привязывания верёвки к карабину. Узлы в арбористикеZIPPER O DISIPADOR CASERO DE VÍA FERRATA MACGIVER