Use 4 stroke Gasoline Engine to run water pump
Hello, this is my next video on "Use 4 stroke Gasoline Engine to run water pump".
I hope you really Enjoy the video. Please stay tune!
1. 4 Stroke Engine:
full travel of the piston along the cylinder, in either direction. The four separate strokes are termed:
Intake: Also known as induction or suction. This stroke of the piston begins at top dead center (T.D.C.) and ends at bottom dead center (B.D.C.). In this stroke the intake valve must be in the open position while the piston pulls an air-fuel mixture into the cylinder by producing vacuum pressure into the cylinder through its downward motion. The piston is moving down as air is being sucked in by the downward motion against the piston.
Compression: This stroke begins at B.D.C, or just at the end of the suction stroke, and ends at T.D.C. In this stroke the piston compresses the air-fuel mixture in preparation for ignition during the power stroke (below). Both the intake and exhaust valves are closed during this stage.
Combustion: Also known as power or ignition. This is the start of the second revolution of the four stroke cycle. At this point the crankshaft has completed a full 360 degree revolution. While the piston is at T.D.C. (the end of the compression stroke) the compressed air-fuel mixture is ignited by a spark plug (in a gasoline engine) or by heat generated by high compression (diesel engines), forcefully returning the piston to B.D.C. This stroke produces mechanical work from the engine to turn the crankshaft.
Exhaust: Also known as outlet. During the exhaust stroke, the piston, once again, returns from B.D.C. to T.D.C. while the exhaust valve is open. This action expels the spent air-fuel mixture through the exhaust valve.
2. Water Pump:
A pump is a device that moves fluids (liquids or gases), or sometimes slurries, by mechanical action, typically converted from electrical energy into hydraulic energy. Pumps can be classified into three major groups according to the method they use to move the fluid: direct lift, displacement, and gravity pumps.[1]
Pumps operate by some mechanism (typically reciprocating or rotary), and consume energy to perform mechanical work moving the fluid. Pumps operate via many energy sources, including manual operation, electricity, engines, or wind power, and come in many sizes, from microscopic for use in medical applications, to large industrial pumps.
Mechanical pumps serve in a wide range of applications such as pumping water from wells, aquarium filtering, pond filtering and aeration, in the car industry for water-cooling and fuel injection, in the energy industry for pumping oil and natural gas or for operating cooling towers and other components of heating, ventilation and air conditioning systems. In the medical industry, pumps are used for biochemical processes in developing and manufacturing medicine, and as artificial replacements for body parts, in particular the artificial heart and penile prosthesis.
When a casing contains only one revolving impeller, it is called a single-stage pump. When a casing contains two or more revolving impellers, it is called a double- or multi-stage pump.
In biology, many different types of chemical and biomechanical pumps have evolved; biomimicry is sometimes used in developing new types of mechanical pumps.
Видео Use 4 stroke Gasoline Engine to run water pump канала Creativity DIY
I hope you really Enjoy the video. Please stay tune!
1. 4 Stroke Engine:
full travel of the piston along the cylinder, in either direction. The four separate strokes are termed:
Intake: Also known as induction or suction. This stroke of the piston begins at top dead center (T.D.C.) and ends at bottom dead center (B.D.C.). In this stroke the intake valve must be in the open position while the piston pulls an air-fuel mixture into the cylinder by producing vacuum pressure into the cylinder through its downward motion. The piston is moving down as air is being sucked in by the downward motion against the piston.
Compression: This stroke begins at B.D.C, or just at the end of the suction stroke, and ends at T.D.C. In this stroke the piston compresses the air-fuel mixture in preparation for ignition during the power stroke (below). Both the intake and exhaust valves are closed during this stage.
Combustion: Also known as power or ignition. This is the start of the second revolution of the four stroke cycle. At this point the crankshaft has completed a full 360 degree revolution. While the piston is at T.D.C. (the end of the compression stroke) the compressed air-fuel mixture is ignited by a spark plug (in a gasoline engine) or by heat generated by high compression (diesel engines), forcefully returning the piston to B.D.C. This stroke produces mechanical work from the engine to turn the crankshaft.
Exhaust: Also known as outlet. During the exhaust stroke, the piston, once again, returns from B.D.C. to T.D.C. while the exhaust valve is open. This action expels the spent air-fuel mixture through the exhaust valve.
2. Water Pump:
A pump is a device that moves fluids (liquids or gases), or sometimes slurries, by mechanical action, typically converted from electrical energy into hydraulic energy. Pumps can be classified into three major groups according to the method they use to move the fluid: direct lift, displacement, and gravity pumps.[1]
Pumps operate by some mechanism (typically reciprocating or rotary), and consume energy to perform mechanical work moving the fluid. Pumps operate via many energy sources, including manual operation, electricity, engines, or wind power, and come in many sizes, from microscopic for use in medical applications, to large industrial pumps.
Mechanical pumps serve in a wide range of applications such as pumping water from wells, aquarium filtering, pond filtering and aeration, in the car industry for water-cooling and fuel injection, in the energy industry for pumping oil and natural gas or for operating cooling towers and other components of heating, ventilation and air conditioning systems. In the medical industry, pumps are used for biochemical processes in developing and manufacturing medicine, and as artificial replacements for body parts, in particular the artificial heart and penile prosthesis.
When a casing contains only one revolving impeller, it is called a single-stage pump. When a casing contains two or more revolving impellers, it is called a double- or multi-stage pump.
In biology, many different types of chemical and biomechanical pumps have evolved; biomimicry is sometimes used in developing new types of mechanical pumps.
Видео Use 4 stroke Gasoline Engine to run water pump канала Creativity DIY
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Custom fat Ebike using DC Motor 24V 350W and Ebike Components](https://i.ytimg.com/vi/Mzwz7WD6CHM/default.jpg)
![#shorts New Video Coming soon!!! #shortvideo #shortsvideo #subscribe](https://i.ytimg.com/vi/bG4YgeqouPI/default.jpg)
![Pumping with 24v dc motor](https://i.ytimg.com/vi/WUNDpH_FCIM/default.jpg)
![#shorts 24V Dc Motor Pump](https://i.ytimg.com/vi/6At2dGbG4hM/default.jpg)
![MAKE 220V MICRO DC MOTOR TO AC GENERATOR](https://i.ytimg.com/vi/kIQgiE3wYEk/default.jpg)
![Create Remote Control Generator 220V 500W from 4 stroke Engine](https://i.ytimg.com/vi/IyBpvWP03yo/default.jpg)
![Fat E-Bike from DC Motor 24V 350W #Shorts](https://i.ytimg.com/vi/8Q3Ua4ZIXSU/default.jpg)
![Upgrade Fat Bike to next level Ebike with 24V 350W Motor Kit](https://i.ytimg.com/vi/bmqBOZVdwog/default.jpg)
![Create Amazing DC Water Pump from Grass Cutter Pump](https://i.ytimg.com/vi/qBpAOYB-llo/default.jpg)
![Motor hacks Energy from Motor 775 & 895 12-24V and Electrolytic Capacitor](https://i.ytimg.com/vi/XQZKxuXfyfY/default.jpg)
![DC Motor hacks: Generator from 24V 250W motor & 4Stroke Engine](https://i.ytimg.com/vi/S63oqHqMGyU/default.jpg)
![Reassembling 25 HP Diesel Engine for running 12KW Generator](https://i.ytimg.com/vi/XuJERhtiKj0/default.jpg)
![Create 30V 5A Power supply using 220V to 12V transformer](https://i.ytimg.com/vi/K5ATHbhDcq4/default.jpg)
![Create Looping Power from 14V AC Generator and 220V Inverter](https://i.ytimg.com/vi/t1NFYandm_4/default.jpg)
![Free Energy Hack: Free Energy from 12-24V DC Motor and Super Capacitors](https://i.ytimg.com/vi/0hR4Zp0kd4I/default.jpg)
![Micro Motor 220V 45W as Generator with 775 dc 12v motor](https://i.ytimg.com/vi/WBEA6j8epKA/default.jpg)
![DC motor hacks: 12V DC Motor 775 to run 24V DC Motor 250W as generator](https://i.ytimg.com/vi/iXCUlZgGvyI/default.jpg)
![Free Energy from Super Capacitors and 12V-24V DC Motors Mechanic](https://i.ytimg.com/vi/RgWZV_wPo0s/default.jpg)
![Create Water Pump from DC Motor 24V](https://i.ytimg.com/vi/wLerM-quJZ0/default.jpg)
![Car Radiator Motor Produces Amazing Power Supply](https://i.ytimg.com/vi/T0bnryHv-Q8/default.jpg)