Aluminum "Mickey Mouse" Flange DIY - BMW E90 N54 N52
You can get the part right here: https://amzn.to/3FSO8M0
I wasn't very clear in the video on why I drain the coolant from above rather than down below. It's because you only have to drain a tiny amount this way and then top it up afterward. I also recently changed my coolant last year when I did my water pump so why replace it as it's still perfectly good.
Another thing I forgot to mention in this video was the bleed procedure. You want to do that after you top off the coolant:
Inside the car, put the key in the ignition, foot OFF the brake, hit the start button. This turns the ignition on. Set your HVAC fan speed to low, temperature to maximum, center button (in the middle of the vents) to hot. Push down on the gas pedal all the way and hold it for 10 seconds. The automatic bleed procedure should be going. You can look inside your coolant reservoir and you should see it spraying out. You can see this procedure in detail by clicking here:
https://youtu.be/hBRe1l5YNhY?t=1911
starting 31:51 in
This video is for entertainment purposes only. 50sKid assumes no liability for any repairs or modifications performed by the viewer as a result of the information contained in this video.
Видео Aluminum "Mickey Mouse" Flange DIY - BMW E90 N54 N52 канала 50sKid
I wasn't very clear in the video on why I drain the coolant from above rather than down below. It's because you only have to drain a tiny amount this way and then top it up afterward. I also recently changed my coolant last year when I did my water pump so why replace it as it's still perfectly good.
Another thing I forgot to mention in this video was the bleed procedure. You want to do that after you top off the coolant:
Inside the car, put the key in the ignition, foot OFF the brake, hit the start button. This turns the ignition on. Set your HVAC fan speed to low, temperature to maximum, center button (in the middle of the vents) to hot. Push down on the gas pedal all the way and hold it for 10 seconds. The automatic bleed procedure should be going. You can look inside your coolant reservoir and you should see it spraying out. You can see this procedure in detail by clicking here:
https://youtu.be/hBRe1l5YNhY?t=1911
starting 31:51 in
This video is for entertainment purposes only. 50sKid assumes no liability for any repairs or modifications performed by the viewer as a result of the information contained in this video.
Видео Aluminum "Mickey Mouse" Flange DIY - BMW E90 N54 N52 канала 50sKid
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Milwaukee High Speed vs Low Speed RatchetsBMW E46 Headlight Reconditioning DIYMilwaukee's Extended Reach High Speed RatchetsBMW E46 Engine & Transmission Mount ReplacementHow To Do A Full DIY Brake Job On An E90 BMWBMW E90 Aftermarket Downpipes DIYBMW E90 Front Mount Intercooler DIYBimmerTech Alpha One Speakers Install DIYBMW charge pipe cracks and fails! - Charge Pipe Upgrade DIY E90 N54 BMWAre Dual Cone Intakes Worth It? - How to install Dual Cone Intakes on a BMW E90 DIYAdd 80HP to your car!! - How To Install, Update, and Use JB4 on the BMW N54 engine for E90 2007-2012BMW E90 Oil Cooler Retrofit DIYMax Out The Stock Turbos On An E90 BMW 335iHow to Super Clean Your BMW EngineOil in your charge pipe? Here's the solution! - BMW E90 PCV Valve UpgradeChemical Cleaning vs Walnut Blasting - N54 Intake Valve Cleaning E90 BMW DIYSolve Your Reduced Power Problems - E90 VANOS Solenoid CleaningLaunch Creader Elite BMW Scan ToolAbout My My Weight LossThis thing sucks to replace! - E46 Steering Angle Sensor DIY Replacement