Audi TT RS 12V Ride On Car Assembly And Pairing Remote Control

A short-ish video showing the complete assembly of our Kids 12V Audi TTRS Ride on Car.
• Make sure that the power switch is turned “OFF” before assembling the ride on.
• Before first time use, charge the battery for at least 4 to 6 hours.
• Assembly tools required: Screwdriver, Spanner, Longnose pliers.

RESOURCES & LINKS:
____________________________________________
For more info on this car, visit http://bit.ly/AudiTTRideOnCars
____________________________________________

Remove all the parts from the rear axle. Slide the gear box onto the rear axle, keep the motor and the connector on the gear box through the larger hole on the rear of the vehicle and out where the battery sits.

Slide the driving wheel onto the rear axle and then match this with the gear box.

Slide the washer onto the rear axle. Hold the other side of the axle for leverage, tighten a lock nut to the end of the rear axle with a spanner.

Repeat on the other side. Now for the front wheels. Remove all parts from the axle. Slide the washer on the axle and then slide the bush onto the axle.

Slide on the wheel and ensure the bush is matched up with the notch on the wheel.

Follow this by sliding the washer onto the axle, then secure the wheel with the locking nut. Repeat on the other side. Then all you need to do is fit the hub caps onto the wheel.

Remove the steering column from the bottom of the car by cutting the cable ties securing it. Turn the vehicle body on its side.

Slide the steering gear box onto the steering column bar. Align the holes in the steering column with the holes in the steering gear box cork.

Tighten the M5X22 machine screw and number 5 nut. Insert the straight end of the steering column up through the hole in the remote control driver. Line up the holes in the r/c driver and the hole in the steering column.

Then fit a number 10 washer to the bent end of the steering column. Insert the split pin into the hole in the steering column, bend the ends of the split pin back to secure. You can use your hands to do this, however, we do recommend that you use the long nose pliers to avoid injury.

Turn the vehicle back onto its wheels, remove the M535 machine screw and 05 nut from the steering wheel. Place the steering wheel over the steering column protruding from the middle of the steering wheelbase.

Align the holes on each end of the steering wheel with the holes at the end of the steering wheel column, forcing the nut on the opposite end of the screw to secure the steering wheel to the steering column. Fit the tabs on the windscreen into the slots on the front, push until you hear it click into place.

Unbuckle seatbelt and move it out of the way to gain a better view of the under-seat compartment. Plug the vehicle connectors into the motor connectors, line up the tabs, push until you hear it click into place.

Repeat this for both motors. Then plug the red fuse connector into the terminal on the battery. Move seatbelt out of the way.

Fit the motor hood on the motor. Tighten four 0412 flathead screws to secure it. Repeat this for both motors. Fit the tabs on the back of the seat into the slots of the rear of the vehicle.

Tighten two M5X60 machine screws with the screwdriver. Fit the seat rest to the rear of the vehicle, push until you hear a click into place.

Line up the tabs, fit the rear spoiler to the rear of the vehicle. Fit the tabs on the mirror into the hole on the vehicle's side, push until you hear a click into place. Repeat on the other side.

To charge the car, find an empty wall socket and ensure that it is switched off.

Plug the charger into the socket, find the charging point in the car and plug the other side of the charger into the charging point. Switch on the wall socket to commence charging. It is recommended that the car's first charge should be between eight and 10 hours.

This is to maintain the efficiency of the battery, so don't be tempted to use the car until this step is undertaken.

Connecting the remote controller. For this step, you will need two AAA batteries, which are not included.

Undo the battery cover on the back of the controller using a Phillips head screwdriver and remove the cover form the controller itself. Then insert two AAA batteries, ensuring the batteries are the correct way around.

Replace the cover and tighten the retaining screw.

The first thing you need to do is find the connection button, which should be found at the top of the remote controller, press the connection button for two to four seconds first, then turn on the power button located on the vehicle dashboard console.

The low-speed indicator should flash into a long bright light. This means the connection is successful. If the indicator only flashes, this means there's a connection failure.

Replace the batteries and repeat the steps. And that's it, that's the end of the instruction for the Audi TT.

#riiroobuild #riiroosquad #rideoncarassembly

Видео Audi TT RS 12V Ride On Car Assembly And Pairing Remote Control канала RiiRoo