BGC 2.2 (2.2b2) GoPro Camera Gimbal – Software, drivers, setup and receiver connections.
In this video I show the new gimbal (BGC 2.2 based) that I will fit to the new Hexcopter I am building for aerial photography. This particular one was bought from eBay for less than £46 and came complete with the control board and brushless motors.
The very basic paper instructions that came with this gimbal can be downloaded from https://dl.dropboxusercontent.com/u/67301981/Gimbal%20Printed%20Instructions.jpg
For a link to the drivers page visit https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
For a link to the BaseCam board software visit http://www.basecamelectronics.com/downloads/8bit/
In this video I show the board and explain the connectors, features and software/drivers you will need to configure any setting on the 2.2b2 8 bit version of the firmware that comes on this board. One setting in particular is useful to reduce/remove the amount of buzzing or humming that you may get from the gimbal in operation.
In addition I also show how to connect the gimbal to a receiver to control pitch and roll manually using a transmitter.
I hope this makes it easier for those of you who are looking at this. In summary – it’s cheap and cheerful and not as powerful as some of the newer 32bit versions of the board but it does the job and is a great starter gimbal.
Thanks for watching, please like and subscribe. My Helpout channel is available if you have any questions.
Happy flying!
Видео BGC 2.2 (2.2b2) GoPro Camera Gimbal – Software, drivers, setup and receiver connections. канала Painless360
The very basic paper instructions that came with this gimbal can be downloaded from https://dl.dropboxusercontent.com/u/67301981/Gimbal%20Printed%20Instructions.jpg
For a link to the drivers page visit https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
For a link to the BaseCam board software visit http://www.basecamelectronics.com/downloads/8bit/
In this video I show the board and explain the connectors, features and software/drivers you will need to configure any setting on the 2.2b2 8 bit version of the firmware that comes on this board. One setting in particular is useful to reduce/remove the amount of buzzing or humming that you may get from the gimbal in operation.
In addition I also show how to connect the gimbal to a receiver to control pitch and roll manually using a transmitter.
I hope this makes it easier for those of you who are looking at this. In summary – it’s cheap and cheerful and not as powerful as some of the newer 32bit versions of the board but it does the job and is a great starter gimbal.
Thanks for watching, please like and subscribe. My Helpout channel is available if you have any questions.
Happy flying!
Видео BGC 2.2 (2.2b2) GoPro Camera Gimbal – Software, drivers, setup and receiver connections. канала Painless360
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Brushless Gimbal Controller setupBGC 2.2b2 Gimbal Quick Tip: Setting (or resetting) the tilt angle manuallyUnboxing Gimbal 2 Axis BGC buat Syma X 8Pro gokil..Tutorial: 2-Achs-Gimbal tunen | PID-Werte | Cheerson CX 20 | DESTorM32 3-axis gimbal default settings test (courtesy GearBest)Pixhawk Gimbal Setup. Fast And Easy!MOST CINEMATIC GIMBAL MOVES + TIPSConfigurando o Gimbal Genérico - visão geral e drivers - (parte I)The ULTIMATE DJI Ronin-S REVIEW and Tutorial Walk-ThroughSimpleBGC and how to find which Firmware you have.PERFECT PID tuning for Alex Mos Basecam Gimbals - Yuri Method (long Alexmos tutorial simplebgc)Camera Gimbal for DJI Phantom (Complete Guide)FPV 2 axis gimbal reviewSimple BGC 3.0 - Firmware upgrade 2.2b2 - 2.40b8 - Deutsch / GermanBuild a Drone Part 3 - Add a Camera Gimbal and FPV TransmitterCheap Gimbal UpdateTarot TL3T05 Gopro 3DⅣ for Gopro Hero 5/6/7 Bench Review and Setup // Camera Drone GimbalHow to: Alexmos/Basecam Controller - Make it work perfectlyGood luck buy gimbal install new boardDIY 3D Printed 4th Axis Gimbal Stabilizer - Pro Model