How-To: Flush Navien Tankless Water Heater with vinegar
How-To: Flush Navien Tankless Water Heater with vinegar
Items Needed:
* sump pump
* 2x water inlet hoses 4-6 feet
* 5 gallon bucket
* approx. 12-14L of 10% strength vinegar
Step-by-Step:
1. Turn off all power to your to your tankless water heater. I turned off the panel, the power switch in the Navien as well as disconnecting the power cord from the power outlet.
2. Close the cold and hot water valves from the unit to the house.
3. Remove the cold and hot water caps, connect your inlet hoses and place the other ends into your bucket.
4. Open the cold and hot water valves from the unit to your inlet hoses to empty water from your unit into the bucket.
5. Remove and clean the cold and hot water screens. Remember to screw back in.
6. Remove and clean the waste trap. Remember to put back in.
7. Place sump pump into bucket and connect the cold water inlet hose to the sump pump.
8. Fill bucket with approx. 12-14L of vinegar or roughly 3/4 full.
9 Plug in sump pump to begin circulating and cleaning. It may take 10-20 seconds for vinegar to begin exiting the hot water inlet hose back into the bucket, during this time you'll see the vinegar level the bucket lower 3-4 inches as the unit is filled with vinegar.
10. Leave running for 60-90 minutes. DO NOT USE WATER IN THE HOUSE.
11. Once cleaning is complete unplug sump pump and essentially reverse the above steps. Check the screens and trap again and clean if necessary.
12. Once the Navien is back up try running the hot water on each facet in the house, one at a time, for a few minutes each. You may see spitting of the water initially, followed by almost kind of a soapy sudsy water though this will clear up. You may even see some scale (mineral deposit) flushed through your facets that will come out as a light brownish water colour, again this will clear up.
13. Lastly dump out the vinegar from your bucket and replace with clean cold water. With one inlet house connected to the pump at a time run in a closed system in the bucket for a couple minutes. Repeat for the other hose.
Congratulations you just saved yourself hundreds of dollars annually!
Видео How-To: Flush Navien Tankless Water Heater with vinegar канала Eric Albrecht
Items Needed:
* sump pump
* 2x water inlet hoses 4-6 feet
* 5 gallon bucket
* approx. 12-14L of 10% strength vinegar
Step-by-Step:
1. Turn off all power to your to your tankless water heater. I turned off the panel, the power switch in the Navien as well as disconnecting the power cord from the power outlet.
2. Close the cold and hot water valves from the unit to the house.
3. Remove the cold and hot water caps, connect your inlet hoses and place the other ends into your bucket.
4. Open the cold and hot water valves from the unit to your inlet hoses to empty water from your unit into the bucket.
5. Remove and clean the cold and hot water screens. Remember to screw back in.
6. Remove and clean the waste trap. Remember to put back in.
7. Place sump pump into bucket and connect the cold water inlet hose to the sump pump.
8. Fill bucket with approx. 12-14L of vinegar or roughly 3/4 full.
9 Plug in sump pump to begin circulating and cleaning. It may take 10-20 seconds for vinegar to begin exiting the hot water inlet hose back into the bucket, during this time you'll see the vinegar level the bucket lower 3-4 inches as the unit is filled with vinegar.
10. Leave running for 60-90 minutes. DO NOT USE WATER IN THE HOUSE.
11. Once cleaning is complete unplug sump pump and essentially reverse the above steps. Check the screens and trap again and clean if necessary.
12. Once the Navien is back up try running the hot water on each facet in the house, one at a time, for a few minutes each. You may see spitting of the water initially, followed by almost kind of a soapy sudsy water though this will clear up. You may even see some scale (mineral deposit) flushed through your facets that will come out as a light brownish water colour, again this will clear up.
13. Lastly dump out the vinegar from your bucket and replace with clean cold water. With one inlet house connected to the pump at a time run in a closed system in the bucket for a couple minutes. Repeat for the other hose.
Congratulations you just saved yourself hundreds of dollars annually!
Видео How-To: Flush Navien Tankless Water Heater with vinegar канала Eric Albrecht
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Christmas Concert 2022 - Day 2 of 2Warden Diaries ~ episode 6Heroes of Middle-earth ❄ Champion Diaries ~ episode 3Highlight: Healer burning my soul in Mythic +5 Motherlode with Bursting in WoW.Roving Threats - Ringló Vale - GundashZon plays LOTRO Guardian in Mordor ~ episode 20Viewer Request: U17.2 L100 Sammath Gûl solo walkthroughZon epic ambush victory.NcF T2 - Legbarthil: 75 Overpower Guardian soloU15-17 Guardian Guide - Chapter 7: PvMP Gear and BuildNcF T2 - Umheryn: 75 Overpower Guardian soloZon Draws chill streamReleasing Sparrow back into wild.Zon plays LOTRO Guardian in Mordor ~ episode 27Highlight: +10 Freehold with bursting, skittish and awakeningLotro 10-year Anniversary and Kinship island tourRoving Threat - Western Gondor - Mota780 input into 480 and 300 outputsHighlight: 🔴 Zon Fornost Fire T1 @ 115 on Guardian ❄ Update 22.2Highlight: 🔴 2-man Guardian CoS T1 ~ 3rd boss @ 115 ❄ Update 22.2Zon plays LOTRO Guardian in Mordor ~ episode 17-1