robot hand || bionic hand prosthesis prototype

This bionic hand is controlled by an Arduino Nano V3 and uses 4 15kg servo's to move the index, middle, ring and little finger and 3 9g servo's to rotate the thumb and pull the thumb and the fingers open. This bionic hand it's structure is modelled after my hand so I could make a gel10 mold that would fit snug around it. I originally wanted to integrate some force feedback in the finger tips by using some small pushbuttons but that didn't turn out to well because the wires from the pushbuttons in combination with the gel10 mold caused to much friction in the joints of the fingers and the fingers had to push to hard to activate the pushbuttons. I'm now going to do some tests with current sensors so I can measure the current going to the servo's and when the current goes above the normal level then the servo's would stop (that's the idea).

STL and Fusion 360 source files can be found here: https://bbprojects.technology/collections/stl-fusion-360-source-files/products/robot-hand-bionic-hand-prosthesis-prototype

more info about this project (parts used, schematics, Arduino code) can be found here: https://bbprojects.technology/blogs/projects/robot-hand-bionic-hand-prosthesis-prototype

My PayPal: https://paypal.me/BrockenBrian

Tools used for this project:

SMD rework station: https://www.banggood.com/YAOGONG-8878D-2-In-1-SMD-Rework-Soldering-Station-Hot-Air-Gun-Welding-Solder-Iron-Repair-Tool-p-1348341.html?p=E01411629100201406T1&custlinkid=1206705

PLA filament: https://www.banggood.com/Creality-3D-White-or-Black-or-Yellow-or-Blue-or-Red-1KG-1_75mm-PLA-Filament-For-3D-Printer-p-1290153.html?p=E01411629100201406T1&custlinkid=926158

Recommended 3D-printer: https://www.banggood.com/Creality-3D-Ender-3-Pro-V-slot-Prusa-I3-DIY-3D-Printer-Kit-p-1346320.html?p=E01411629100201406T1&custlinkid=677427

Components used:

4 × 15kg Servo's
link: https://www.banggood.com/MG995-High-Torgue-Mental-Gear-Analog-Servo-p-73885.html?rmmds=search&cur_warehouse=CN

1 × 2.54mm Single Row Male Pin Header Strip For Arduino
link: https://www.banggood.com/10-Pcs-40-Pin-2_54mm-Single-Row-Male-Pin-Header-Strip-For-Arduino-p-918427.html?rmmds=search&cur_warehouse=CN

2 × 9g servo's
link: https://www.banggood.com/TowerPro-SG90-Mini-Gear-Micro-Servo-9g-For-RC-Airplane-Helicopter-p-1009914.html?p=E01411629100201406T1&custlinkid=359550

1 × arduino nano V3
link: https://www.banggood.com/Geekcreit-ATmega328P-Nano-V3-Module-Improved-Version-With-USB-Cable-Development-Board-For-Arduino-p-933647.html?p=E01411629100201406T1&custlinkid=255135

1 × DC-DC Step Down Adjustable Constant Voltage Current Power Supply Module
link: https://www.banggood.com/LM2596-DC-DC-Verstellbar-Step-Down-Schaltregler-Power-Supply-Module-p-88252.html?p=E01411629100201406T1&custlinkid=255154

1 × 2S lipo 7.4V
link: https://www.banggood.com/7_4V-2S-2000mAh-8C-Lipo-Battery-Compatible-for-Frsky-ACCST-Taranis-Q-X7-Transmitter-p-1249125.html?p=E01411629100201406T1&custlinkid=669244

2 × 5mm red LED
link: https://www.banggood.com/Geekcreit-375pcs-3MM-5MM-LED-Light-Emitting-Diode-Beads-Resistance-Lights-Kits-Bulb-Lamp-p-1027601.html?p=E01411629100201406T1&custlinkid=669272

2 × pushbutton
link: https://www.banggood.com/100pcs-Mini-Micro-Momentary-Tactile-Tact-Switch-Push-Button-DIP-P4-Normally-Open-p-917570.html?p=E01411629100201406T1&custlinkid=669260

2 × 200 ohm resistor
link: https://www.banggood.com/Wholesale-Geekcreit-600pcs-30-Kinds-Value-1-14W-Metal-Film-Resistor-Assorted-Kit-20pcs-Each-Value-p-53320.html?rmmds=search&cur_warehouse=CN

3 × springs from old pens

1 × 1mm diameter steel rod or similar as shafts for the fingers

1 × nylon wire

1 × somewhat larger spring but less stiff as the springs from the pens
this spring brings the thumb back to it's original position. I just used one I had lying around and I thought was gonna work

If you're wondering how I do what I do and how you can get started creating your own prototypes I wrote a basic guide about it.
Part 1: Mechanical design can be found here: https://brian-brocken.medium.com/basic-guide-to-start-developing-your-own-products-part-1-mechanical-design-1f13d2074ebb
Part2: PCB design can be found here: https://brian-brocken.medium.com/basic-guide-to-start-developing-your-own-products-part-2-pcb-design-8295b9f8ce25

Видео robot hand || bionic hand prosthesis prototype канала Brian Brocken