Yamaha XJ600 Diversion / Seca 2 - Clutch Rattle / Engine noise fix.
If you would like to help, see how by clicking the read more link at the bottom of this text.
The Yamaha XJ600 Diversions / Seca 2 can suffer an annoying rattle, one of the causes of this rattle, is well documented on the xjrider.com forum along with a recommended fix. You commonly hear that the noise is caused by clutch rattle but that's not entirely accurate. There are four causes of that noise heard at idle and oil pump drive gear noise is at the bottom:
Carb synchronization - this has to be spot on or it makes noise as the pistons/crankshaft have force applied differently.
Carburetor pilot screws mis-adjusted - this causes each cylinder to fire differently and results in noise at idle, similarly to carb synchronization.
Gearbox wear - as the shift forks and the gear teeth wear, the tolerances increase. This allows the shift forks, synchronizers and gears to move around as the engine idles (albeit a small bit) resulting in noise.
Oil pump drive gear - you already went after that.
Start with a very thorough and accurate synchronization of the carbs, then set the pilot screws consistently, then change the oil to a heavier weight (temperature appropriate, of course) and see how your idle sounds.
This video shows the steps highlighted in the guide on the xjrider.com forum. If attempting this fix yourself, the risk and the potential damage that can be done is yours, and yours alone. I made this video to show the steps involved, and whilst not complicated or hard to achieve, could have adverse affects, I'm not a mechanic and am not pretending to be, but am happy to video what I did to resolve this issue. If you are going to attempt this yourself, make sure you watch the video all the way through first, and look at the guide on the xjrider.com forum as well, there are specific tools needed to complete the job, so make sure you have everything prior to starting. Good luck
If you would like to help keep the lights on and contribute to the channel you can donate as little as 1$ per video or a maximum per month on my Patreon page - www.patreon.com/gtsgarage
If you would prefer a one off donation as appreciation for something you've learnt on the channel, you can donate to paypal.me/buckinghamjf
If you are looking for any of the tools or products i use in the garage, you can also help the channel by using the links below and purchasing the product through my affiliation with Amazon. I also get a smaller amount, by just opening the page through one of my links below and browsing to any product of your choice.
Teng 7 Piece Screw Driver Set- https://www.amazon.co.uk/gp/product/B000Y8JFAY/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B000Y8JFAY&linkId=7a6d9d2eeef063620ee95f9e99573db5
Parker 200Amp Welder - https://www.amazon.co.uk/gp/product/B01CXKOV9U/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B01CXKOV9U&linkId=f1201bbaf3b6bf436cb0bb072ef64019
Motorcycle Lift 1000lbs - https://www.amazon.co.uk/gp/product/B01J4AXPA8/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B01J4AXPA8&linkId=be67c99a9d33a881fef3e56dbc6ffcad
Ryde Wheel Chock https://www.amazon.co.uk/gp/product/B01MRSBW8S/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B01MRSBW8S&linkId=0d8bb196e92fe6f07870472565631af8
Paint Stripper - https://www.amazon.co.uk/gp/product/B00A7RMPGS/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B00A7RMPGS&linkId=389c5dfdcdbeefb060bd8777062a879f
Видео Yamaha XJ600 Diversion / Seca 2 - Clutch Rattle / Engine noise fix. канала GTs Garage
The Yamaha XJ600 Diversions / Seca 2 can suffer an annoying rattle, one of the causes of this rattle, is well documented on the xjrider.com forum along with a recommended fix. You commonly hear that the noise is caused by clutch rattle but that's not entirely accurate. There are four causes of that noise heard at idle and oil pump drive gear noise is at the bottom:
Carb synchronization - this has to be spot on or it makes noise as the pistons/crankshaft have force applied differently.
Carburetor pilot screws mis-adjusted - this causes each cylinder to fire differently and results in noise at idle, similarly to carb synchronization.
Gearbox wear - as the shift forks and the gear teeth wear, the tolerances increase. This allows the shift forks, synchronizers and gears to move around as the engine idles (albeit a small bit) resulting in noise.
Oil pump drive gear - you already went after that.
Start with a very thorough and accurate synchronization of the carbs, then set the pilot screws consistently, then change the oil to a heavier weight (temperature appropriate, of course) and see how your idle sounds.
This video shows the steps highlighted in the guide on the xjrider.com forum. If attempting this fix yourself, the risk and the potential damage that can be done is yours, and yours alone. I made this video to show the steps involved, and whilst not complicated or hard to achieve, could have adverse affects, I'm not a mechanic and am not pretending to be, but am happy to video what I did to resolve this issue. If you are going to attempt this yourself, make sure you watch the video all the way through first, and look at the guide on the xjrider.com forum as well, there are specific tools needed to complete the job, so make sure you have everything prior to starting. Good luck
If you would like to help keep the lights on and contribute to the channel you can donate as little as 1$ per video or a maximum per month on my Patreon page - www.patreon.com/gtsgarage
If you would prefer a one off donation as appreciation for something you've learnt on the channel, you can donate to paypal.me/buckinghamjf
If you are looking for any of the tools or products i use in the garage, you can also help the channel by using the links below and purchasing the product through my affiliation with Amazon. I also get a smaller amount, by just opening the page through one of my links below and browsing to any product of your choice.
Teng 7 Piece Screw Driver Set- https://www.amazon.co.uk/gp/product/B000Y8JFAY/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B000Y8JFAY&linkId=7a6d9d2eeef063620ee95f9e99573db5
Parker 200Amp Welder - https://www.amazon.co.uk/gp/product/B01CXKOV9U/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B01CXKOV9U&linkId=f1201bbaf3b6bf436cb0bb072ef64019
Motorcycle Lift 1000lbs - https://www.amazon.co.uk/gp/product/B01J4AXPA8/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B01J4AXPA8&linkId=be67c99a9d33a881fef3e56dbc6ffcad
Ryde Wheel Chock https://www.amazon.co.uk/gp/product/B01MRSBW8S/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B01MRSBW8S&linkId=0d8bb196e92fe6f07870472565631af8
Paint Stripper - https://www.amazon.co.uk/gp/product/B00A7RMPGS/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=gtsgarage-21&creative=6738&linkCode=as2&creativeASIN=B00A7RMPGS&linkId=389c5dfdcdbeefb060bd8777062a879f
Видео Yamaha XJ600 Diversion / Seca 2 - Clutch Rattle / Engine noise fix. канала GTs Garage
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
YAMAHA XJ600 Diversion repair - Clutch noise / kuplung zaj megszüntetéseMotorcycle Clutch Replacement XJ650 YamahaYamaha XJ600 valve adjustmentDelboy's Garage, Motorcycle Clutch Replacement .HEIA-FR P1 : Yamaha XJ 600 Motor Reverse EngineeringYamaha JX600 Diversion Oil changeYamaha XS650 clutch housing, clutch boss, removal and replacementYamaha XJ 600 S Diversion Video 4 Vergaser demontierenYamaha XJ6 Diversion clutch plate replacement.How multiplate clutches work! (Animation)Yamaha XJ 600 4BR, 4LX, RJ011 - Repair of the primary drive - Tutorial, DIYYamaha XJ 600 S Diversion - KettensatzwechselYamaha XJ - napinacz łańcucha rozrząduHow to rebuild a Clutch plate,lining, and polish, clutch box| Fitting in a Truck|pakistani Truck|Suzuki SV650 Rattle Noise Clutch FaultCafe Racer Timelapse build - Yamaha XJ 600 (FJ 600)Yamaha R1 - clutch basket repairBiggest MISTAKE ever, buying $800 Auction BikeMotoTech Tutorial #12 - Kupplung wechseln und RICHTIG einstellenYamaha XJ600 - wymiana zestawu napędowego.