New version of JDY 10 to Bluetooth Receiver | JLCPCB | The H Lab
This is my video about the new version of "Convert JDY 10 to Bluetooth rx for small Bluetooth RC car". This version running Arduino Nano with extern crystal 16Mhz. With this frequency, MCU now able to communicate with JDY 10 at baud 115200, the most stable baud of JDY 10 and also help the Receiver board run faster, without delay. The ATMega328P chip on this new board also have a perfect PWM precise than ATTiny 85 on old version. The board has been tested on our new Hot Wheels Nissan Skyline Silvia 1:64.
The PCB ordered from JLCPCB:
PCBA from $0 (Free Setup, Free Stencil) https://jlcpcb.com/RHS
======================================
Page: https://www.facebook.com/TheHLab
GitHub: https://github.com/thehlab
3D model: https://sketchfab.com/thehlab
======================================
Thank for watching.
The H Lab.
Видео New version of JDY 10 to Bluetooth Receiver | JLCPCB | The H Lab канала The H Lab
The PCB ordered from JLCPCB:
PCBA from $0 (Free Setup, Free Stencil) https://jlcpcb.com/RHS
======================================
Page: https://www.facebook.com/TheHLab
GitHub: https://github.com/thehlab
3D model: https://sketchfab.com/thehlab
======================================
Thank for watching.
The H Lab.
Видео New version of JDY 10 to Bluetooth Receiver | JLCPCB | The H Lab канала The H Lab
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Full convert 1/64 Ford Ranger Raptor to RC | The H Lab](https://i.ytimg.com/vi/HzsFu9FZ-sY/default.jpg)
![Unboxing Porsche 911 GT3 RS vs Porsche Macan Turbo Welly FX](https://i.ytimg.com/vi/Jbasoi-FSLo/default.jpg)
![Car lifts for RC 1:64 to 1:76 scale | The H Lab](https://i.ytimg.com/vi/nQkjvdLGCcM/default.jpg)
![Finally my 3D printed off road car can run](https://i.ytimg.com/vi/-u2pLtA0WIU/default.jpg)
![How to make 1:64 dyno | JLCPCB | The H Lab](https://i.ytimg.com/vi/KzvcNES34_s/default.jpg)
![Modify Servo SG90 increase turn angle | The H Lab](https://i.ytimg.com/vi/Qr4TAQXisO8/default.jpg)
![A gift from Diatone | The H Lab](https://i.ytimg.com/vi/BgGOJQeFAWI/default.jpg)
![Hot Wheels Nissan Skyline Silvia 1:64 RC | The H Lab | Part 3. Completed and Run](https://i.ytimg.com/vi/L8IKSyq_39U/default.jpg)
![Micro 4WD FPV RC Car SNTY60 | The H Lab #shorts](https://i.ytimg.com/vi/_EX5DKngkr0/default.jpg)
![Hot Wheels Nissan Skyline Silvia 1:64 RC | The H Lab | Part 2. Steering system](https://i.ytimg.com/vi/--lufDJ3R7o/default.jpg)
![3D Printed RC boat with air propeller | The H Lab](https://i.ytimg.com/vi/0Lu_kEwE3ys/default.jpg)
![Hot Wheels Nissan Skyline Silvia 1:64 RC | The H Lab | Part 1. Rear engine](https://i.ytimg.com/vi/8vNMgcN4r9w/default.jpg)
![Tesla Cybertruck RC | Bluetooth Control | The H Lab](https://i.ytimg.com/vi/Vw29g1h3XWo/default.jpg)
![Tiny 2 Speed Gear box Double Clutch for 1:24 RC | JLCPCB | The H Lab](https://i.ytimg.com/vi/4HgdzZ1xaos/default.jpg)
![3D Printed Chassis with 4 Links suspension for 1/24 Off Road Car](https://i.ytimg.com/vi/Kk5CQxNTcbo/default.jpg)
![Porsche Macan Rear Electric Axle - 3D Printed | TheHLab](https://i.ytimg.com/vi/yFzvvjHl5M8/default.jpg)
![Micro 4WD FPV RC car SNT Y60 | The H Lab](https://i.ytimg.com/vi/qpfK6HqGLoI/default.jpg)
![How to setup cheap and easiest mini FPV for beginners | The H Lab](https://i.ytimg.com/vi/kwFsMDCOBKE/default.jpg)
![3D Printed RC Boat | The H Lab #shorts](https://i.ytimg.com/vi/LiW_Ca6_xpM/default.jpg)
![3D Printed Mercedes Benz gear shifter | The H Lab](https://i.ytimg.com/vi/nQdxbNNoi7M/default.jpg)