Remove front end loader from Simplicity Legacy
Includes a demonstration of the loader articulation. In this video I remove the loader and hitch frame for it, in preparation for switching to my winter snow setup. I installed these items in the spring but this is the first time I ever removed them.
0:00 Intro
0:51 (long) cold start
1:22 Loader articulation
2:41 Walk-around
4:14 Dismounting loader instructions
4:55 Driving to storage location
6:38 Remove nuts from mounting bolts
7:52 Back tractor from loader
8:40 Retract cylinders & back
11:00 Extend lift cylinders
13:25 Reverse tractor from loader
14:35 Remove pump from PTO
16:05 Reverse tractor, completing FEL removal
17:23 Lift and struggle with FEL on pallet...
19:23 Begin hitch frame removal
Видео Remove front end loader from Simplicity Legacy канала kevin9c1
0:00 Intro
0:51 (long) cold start
1:22 Loader articulation
2:41 Walk-around
4:14 Dismounting loader instructions
4:55 Driving to storage location
6:38 Remove nuts from mounting bolts
7:52 Back tractor from loader
8:40 Retract cylinders & back
11:00 Extend lift cylinders
13:25 Reverse tractor from loader
14:35 Remove pump from PTO
16:05 Reverse tractor, completing FEL removal
17:23 Lift and struggle with FEL on pallet...
19:23 Begin hitch frame removal
Видео Remove front end loader from Simplicity Legacy канала kevin9c1
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Install snow cab on Simplicity Legacy, part 2](https://i.ytimg.com/vi/0YnLMJJ9D-U/default.jpg)
![Whole house test run of the WEN GN875i 7000W open frame inverter generator](https://i.ytimg.com/vi/UqwfiYXSE7I/default.jpg)
![2005 Cadillac STS 5L50E valve body replacement](https://i.ytimg.com/vi/WCLOf1UxDRE/default.jpg)
![Deutz hydro belt idler and tach/hour meter install](https://i.ytimg.com/vi/QzNX3QogHEE/default.jpg)
![GM SPS programming with MDI, Part 4 (refuse to give up)](https://i.ytimg.com/vi/OVe7_WAerOI/default.jpg)
![Mr Cool DIY Gen 4 @ -8F: Does it heat?](https://i.ytimg.com/vi/cajsNGrYiHI/default.jpg)
![2007 Mercedes S550 4Matic: replace rear caliper pistons and seals](https://i.ytimg.com/vi/JYB_OBI5HC0/default.jpg)
![Trying new tach on snow tractor](https://i.ytimg.com/vi/axiMmfs3Ozk/default.jpg)
![Kohler V-twin/Simplicity Legacy 20 no crank issue part 2](https://i.ytimg.com/vi/ETVAj3hvz74/default.jpg)
![Long crank cold start of Briggs opposed twin](https://i.ytimg.com/vi/q6A5fyziUS8/default.jpg)
![Checking generator load status (part 3 of 3)](https://i.ytimg.com/vi/WuaFHvweCwA/default.jpg)
![2004 Mercedes E55 AMG front suspension clunk diagnosis](https://i.ytimg.com/vi/JQrlq5bNJbY/default.jpg)
![NC Trip 2011, backroads 2](https://i.ytimg.com/vi/rJm3aEz3qmI/default.jpg)
![Install impeller flaps on a 46" single stage snow blower](https://i.ytimg.com/vi/f8cJJXtFULA/default.jpg)
![Mr Cool outside unit replacement](https://i.ytimg.com/vi/dxqTIHaozcE/default.jpg)
![Seekonk Speedway Spectator Drags, Scout Night 9/14/19](https://i.ytimg.com/vi/fBY5gCLt8cU/default.jpg)
![Checking out the Deutz-Allis 613H (Simplicity 5212.5)](https://i.ytimg.com/vi/t9yu7wk33NE/default.jpg)
![GM SPS programming with Tech 2, Part 2 (programming attempts)](https://i.ytimg.com/vi/ST4-yYyLZnY/default.jpg)
![First start on the Simplicity 5212.5 after new fuel line](https://i.ytimg.com/vi/PXuXx4SN7pM/default.jpg)
![2008 SRX -7F cold start](https://i.ytimg.com/vi/aT-mXvOaV5Y/default.jpg)