010 - STM32F1 GPIO OUTPUT SETUP AND LED BLINK
The objective of the video is blinking the integrated green LED of the Blue Pill, the steps to for the blinking is as bellow:
1- Have a look into the Board
2- Take a look to the schematics
3- Check the Clock Control Block diagram into the Data sheet
4- Take a look to the Reference manual RCC / GPIO
5- Set up the project
6- Set up the testing envirement
8- Add the easy library
9- start Main
10- Set as low (Check into the debug mode) - Check the Board
11- Set as high (Check into the debug mode) - Check the Board
12- Create the Wait function (Check into the debug mode) - Check the Board
link for the code:
https://github.com/weewStack/STM32F1-Tutorial/tree/master/010-STM32F1_OUTPUT
Link for the board:
https://www.amazon.com/Aideepen-STM32F103C8T6-Minimum-Development-Learning/dp/B078KFK12V/ref=as_sl_pc_tf_til?tag=weew0f7-20&linkCode=w00&linkId=9dd8fdc52d2fabe1b89ff58a14fe6216&creativeASIN=B078KFK12V
Link for the debugger:
https://www.amazon.com/Aideepen-STM32F103C8T6-Minimum-Development-Learning/dp/B078KFK12V/ref=as_sl_pc_tf_til?tag=weew0f7-20&linkCode=w00&linkId=9dd8fdc52d2fabe1b89ff58a14fe6216&creativeASIN=B078KFK12V
Видео 010 - STM32F1 GPIO OUTPUT SETUP AND LED BLINK канала WeeW - Stack
1- Have a look into the Board
2- Take a look to the schematics
3- Check the Clock Control Block diagram into the Data sheet
4- Take a look to the Reference manual RCC / GPIO
5- Set up the project
6- Set up the testing envirement
8- Add the easy library
9- start Main
10- Set as low (Check into the debug mode) - Check the Board
11- Set as high (Check into the debug mode) - Check the Board
12- Create the Wait function (Check into the debug mode) - Check the Board
link for the code:
https://github.com/weewStack/STM32F1-Tutorial/tree/master/010-STM32F1_OUTPUT
Link for the board:
https://www.amazon.com/Aideepen-STM32F103C8T6-Minimum-Development-Learning/dp/B078KFK12V/ref=as_sl_pc_tf_til?tag=weew0f7-20&linkCode=w00&linkId=9dd8fdc52d2fabe1b89ff58a14fe6216&creativeASIN=B078KFK12V
Link for the debugger:
https://www.amazon.com/Aideepen-STM32F103C8T6-Minimum-Development-Learning/dp/B078KFK12V/ref=as_sl_pc_tf_til?tag=weew0f7-20&linkCode=w00&linkId=9dd8fdc52d2fabe1b89ff58a14fe6216&creativeASIN=B078KFK12V
Видео 010 - STM32F1 GPIO OUTPUT SETUP AND LED BLINK канала WeeW - Stack
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
000 - STM32F1 Tutorial Introduction VideoFITA LED RGB | Curso de Arduino #138Program GPIO controls on a DIY Raspberry Pi Arcade Cabinet! HOW TO DO IT EASY!How to Program STM32F103C8 using Keil uVision & STM32CubeMXUnbricking Atmel AVRsEEVblog #1144 - Padauk Programmer Reverse EngineeringSTM32F401 - Configuración de puertos GPIO a nivel de registros (KEIL uVISION)Easy & Powerful Arduino Alternative? STM32 Beginner's GuideКак подключить Led Panel P10 к микроконтроллеру STM32.retropie - how to connect and configure GPIO buttons to raspberry Pi 3 using GPIOnextPhysical computing: HowTo control LEDs, electric motors or servos through GPIOsSTM32F103 GPIO CONFIGURATIONHow to Build a 3D Printer (The Ultimate Guide)GPIO Register OverviewSTM32 Programming Tutorial for Custom Hardware | SWD, PWM, USB, SPI - Phil's Lab #13Raspberry Pi Blinking LEDHow to Install the STM32 USB Bootloader, New Version! (Blue Pill F103C8T6)Introducción a la tarjeta DevEBox STM32H7XX con stm32cubemx and stm32cubeide085-STM32F1 Timer Electronic Speed Controller ESC driver setup for brushless motor