Raspberry PI 3 B+ How to Enable & Test UART Tx/Rx
This video explains how to enable UART on RPI 3 B+ for a serial communication.
On a Raspberry Pi 3, you should use /dev/ttyS0 for UART communication.
/dev/ttyS0: This is typically the UART serial port available for general use.
Disable LOGIN SHELL to be accessible over serial
Serial port hardware only to be enabled
serial login shell disabled
Serial interface is enabled
REBOOT required for changes to take effect
On the Raspberry Pi, the serial port /dev/serial0 is a symlink that points to the actual UART device, which can be either /dev/ttyAMA0 (the primary UART) or /dev/ttyS0 (the secondary UART).
ls -l /dev/serial0
This will show you whether /dev/serial0 points to ttyAMA0 or ttyS0.
in code you can use the symlink serial0 instead of ttyS0
Before executing a python script
prefer using a virtual environment, first create and activate it:
python3 -m venv myenv
source myenv/bin/activate
Then install pyserial within the virtual environment:
pip install pyserial
Видео Raspberry PI 3 B+ How to Enable & Test UART Tx/Rx канала Saravanan AL
On a Raspberry Pi 3, you should use /dev/ttyS0 for UART communication.
/dev/ttyS0: This is typically the UART serial port available for general use.
Disable LOGIN SHELL to be accessible over serial
Serial port hardware only to be enabled
serial login shell disabled
Serial interface is enabled
REBOOT required for changes to take effect
On the Raspberry Pi, the serial port /dev/serial0 is a symlink that points to the actual UART device, which can be either /dev/ttyAMA0 (the primary UART) or /dev/ttyS0 (the secondary UART).
ls -l /dev/serial0
This will show you whether /dev/serial0 points to ttyAMA0 or ttyS0.
in code you can use the symlink serial0 instead of ttyS0
Before executing a python script
prefer using a virtual environment, first create and activate it:
python3 -m venv myenv
source myenv/bin/activate
Then install pyserial within the virtual environment:
pip install pyserial
Видео Raspberry PI 3 B+ How to Enable & Test UART Tx/Rx канала Saravanan AL
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Ultrasonic Distance Measurement with VOICE PLAYBACKHow to Enable Multiple UARTs on RASPBERRY PI 4 & 5I2C LCD 16x2 - Built in I2C AIP31068 Controller#21 DWIN Modbus RS485 MasterIndustrial Modbus (Slave) RTU 8-ch Relay Module /Digital in/ Analog in with RS485 InterfaceBreadBoard with Power Supply#22 ModBus RS485 DWIN Master AI & AO - INPUT & HOLDING REGISTERS Commands 0x04, 0x03,0x06,0x10Proteus - Simulation of L293 Motor Drive IC#18 DWIN Multi Data Multi Page Save and Read from FLASH#10- 4.3" SHELL- LM35 Data on DWIN DMG48270 C043_15WTR-- 8MB FLASH -23.ICL for Images -no 32.ICLOrganize your dual boot Startup screenWindows 8 -Working with Tiles- Getting back Start MenuXBEE Radios - A quick ReferenceTARANG XBEE Modules - Part 2 AT CommandsMastering XBEE - Lesson 7 - Addressing Modes & AT Commands#24 MODBUS RS485 - DWIN as SLAVE - Upgraded - No 22.bin settings#4 HLK BLE 5.0 -How To Transmit DHT11 Data to Masters#17 DWIN Convert Video to AnimationBluetooth BLE REYAX RYB 080I_LITE Getting Started with AT CommandsBLYNK IOT Lesson 4 - DHT SENSOR PUSH DATA