Timing Belt, Water Pump, Pulleys, & Seals - 1MZFE Lexus ES300 Redo Project - Stage 1

This video is the first stage of a Lexus ES300 (3rd Generation) make over project and will show you, step-by-step, how to replace the timing belt, water pump, idler pulley, tensioner pulley, cam and crank seals. This car has over 160K miles, the timing belt had slipped, the water pump and pulleys seized, and many parts were either worn out or in need of replacement. The V6 1MZFE engine is shared with other Toyota based vehicles such as the: Camry V6, Solara V6, Highlander V6, Sienna, Avalon and Lexus RX300. Since the ES 300 engine ( 1MZFE) is shared with other Toyota vehicles, the service being performed on this vehicle can be duplicated on the V6 Camry, Avalon, Solara and other Toyota vehicles as well. This engine is not VVTI (valve interference engine found in the 3MZFE) so a broken timing belt can be installed with a new belt without worry of internal engine damage such as bent valves. To perform this procedure on the 3MZFE engine, refer to these videos (Sienna & Camry 3MZFE):

https://youtu.be/0rCVDLM2hzE
https://youtu.be/jfxGNo9KlFk

Toyota 1MZFE Parts and Specialty Tool:

Timing Belt & Water Pump Component Kit (Good kit … comes with OEM Mitsuboshi Timing Belt, Aisin Water Pump & GMB Bearings):
https://amzn.to/2VQsUE3

Aisin TKT-024 Engine Timing Belt Kit with Water Pump
https://amzn.to/2Q6FHV5

Toyota 90311-38034 Seal, Type T Oil (Cam Seal)
https://amzn.to/2N9L4k6

Toyota 90311-40022 Type-T Engine Crankshaft Oil Seal
https://amzn.to/2Lp0cIa

Bando OEM Power Steering Belt:
https://amzn.to/2U9qt2m

Bando OEM Alternator / AC Belt:
https://amzn.to/2TvMIuS

Torque Strut Rod:
https://amzn.to/2TgJ4EV

DEWALT DW4901 1-Inch Crimped End Wire Brush:
https://amzn.to/2FeWbBw

22 mm High Mass Harmonic Balancer Bolt Removal Socket
https://amzn.to/34yceXj

OEMTOOLS High Mass 6 Piece Crank Bolt Socket Set, 6 Pack
https://amzn.to/2G9ZNpF

Camshaft Seal Removal Tool:
https://amzn.to/2u0rWZV

Camshaft Seal Installation Tool:
https://amzn.to/2F1Nlag

Telescoping 2" Round Inspection Mirror:
https://amzn.to/2TJtmHI

Permatex 22058 Dielectric Tune-Up Grease:
https://amzn.to/2Y06stU

Chain Strap Wrench:
https://amzn.to/2F6ODCo

Right Angle Portable Electric Drill (for the Wire Cup Brush):
https://amzn.to/2UNXYs7

Wire Cup Brush:
https://amzn.to/2WUjacv

Oxygen Sensor Wrench:
https://amzn.to/2Ijw1Rr

If you do not feel comfortable using a chain strap wrench to remove the camshaft pulley bolt, you can try using a universal pulley holder tool. You'll need to use this in conjunction with a "cheater bar".

OTC Universal Pulley Holder:
https://amzn.to/2HKUArb

Harmonic Balancer Puller Tool:
https://amzn.to/2XQQXoo

Star / E Socket Set:
https://amzn.to/2F9jCwo

Toyota Antifreeze Coolant:
https://amzn.to/2O98L9Q

Lisle 24680 Spill-Free Funnel:
https://amzn.to/2OawLJL

Powered Impact Tool (not the one I used, but less expensive quality corded version):
https://amzn.to/2F57ldk

As an Amazon associate, I earn from qualifying purchases. Thank you for your support!

Please Subscribe: https://goo.gl/x6fySQ

Видео Timing Belt, Water Pump, Pulleys, & Seals - 1MZFE Lexus ES300 Redo Project - Stage 1 канала Hardly Moving Productions