The 9 Hour Build - Ep.1: Preparing the Body and Neck
Welcome to Crimson Guitars https://www.youtube.com/user/CrimsonCustomGuitars?sub_confirmation=1 and welcome to Crimson Guitars http://www.crimsonguitars.com and another moment of madness from Ben Crowe. Last week he decided to challenge himself, yet again. This time, the goal is to build a Crimson Guitars PAF solid body in 9 hours or less!
The cameras started rolling at 10:30am on Thursday morning and caught every glorious detail of the build. We now invite you to join him on this journey and follow minute by minute as this guitar comes to life.
Similar to the 12-hour build, (http://tinyurl.com/hhtmszo) this challenge takes place over a normal working day, so expect questions, distractions, and "team support" (heckling).
In this episode, Ben prepares and cuts out the neck
Chapters
0:00 Introduction
4:00 Stopwatch started - neck template out and Ben is beginning the build.
8:25 Nut line has been drawn, now marking routing line for the truss rod
8:54 Coffee and off to the factory floor
11:20 Measure, measure, cut. Now begin routing the truss rod and carbon fibre channels
23:16 Routing for the truss rod access
25:22 Cutting out the neck on the bandsaw
27:43 Belatedly remembered to cut the backplates before cutting out the neck. Oh, Ben.
30:45 Now to finish cutting out the neck
33:35 Working out the headstock angle
37:21 Working out the thickness of the neck and nut placement
39:26 Which bandsaw?
44:30 Masking tape and superglue trick!
47:00 New Triton Router Table comes into play
53:27 Cameraperson changeover and on to episode 2
__________________________________________________________________________________________
Thank you for watching this episode, we hope that you will continue watching and enjoy the entire series. We will be releasing two episodes every day at 10:30am and 6pm until the end of the build. With the final demo by Toby James and Phil Walker on Saturday. Enjoy!
We'd like to thank our partners for helping to make this video series possible.
Triton Tools - http://www.tritontools.com/en-GB
Wagner Meters - https://www.wagnermeters.com/
ISOtunes Bluetooth Hearing Protection - http://bit.ly/36YmKro
Support us by supporting our Partners, and at the same time get yourself a great deal with ISOtunes. Use code "CRIMSON10" for £10 off at "isotunes.co.uk" or $10 off at "isotunes.com"
Get the Freshest CA glues in the market (USA orders) at www.starbond.com
Use Code 'CRIMSONGUITAR' at checkout to save 15% off on your purchase https://www.starbond.com/?rfsn=4953733.fb5f31 _________________________________________________________________________________________
WEBSITE: http://www.crimsonguitars.com
Luthier’s Tools & Supplies: http://bit.ly/LuthTools
Guitar Building Courses: http://bit.ly/LuthierySchool
Kit Guitars: http://bit.ly/KitGuitars
SOCIAL
Instagram - https://www.instagram.com/crimsonguitars/
Facebook -https://www.facebook.com/CrimsonCustomGuitars/
As always, thank you so much to our Patrons, who help make videos like this possible.
Patreon –https://www.patreon.com/crimsonguitars
OTHER Ben's Vintage Tool Shop - https://vintagetoolshop.com/
Thank you again for all your support, we really, really appreciate it! – Ben
Stay tuned and stay awesome! _________________________________________________________________________________________
Please click 'Like' and subscribe. We appreciate your support.
Thanks for watching.
Видео The 9 Hour Build - Ep.1: Preparing the Body and Neck канала Crimson Custom Guitars
The cameras started rolling at 10:30am on Thursday morning and caught every glorious detail of the build. We now invite you to join him on this journey and follow minute by minute as this guitar comes to life.
Similar to the 12-hour build, (http://tinyurl.com/hhtmszo) this challenge takes place over a normal working day, so expect questions, distractions, and "team support" (heckling).
In this episode, Ben prepares and cuts out the neck
Chapters
0:00 Introduction
4:00 Stopwatch started - neck template out and Ben is beginning the build.
8:25 Nut line has been drawn, now marking routing line for the truss rod
8:54 Coffee and off to the factory floor
11:20 Measure, measure, cut. Now begin routing the truss rod and carbon fibre channels
23:16 Routing for the truss rod access
25:22 Cutting out the neck on the bandsaw
27:43 Belatedly remembered to cut the backplates before cutting out the neck. Oh, Ben.
30:45 Now to finish cutting out the neck
33:35 Working out the headstock angle
37:21 Working out the thickness of the neck and nut placement
39:26 Which bandsaw?
44:30 Masking tape and superglue trick!
47:00 New Triton Router Table comes into play
53:27 Cameraperson changeover and on to episode 2
__________________________________________________________________________________________
Thank you for watching this episode, we hope that you will continue watching and enjoy the entire series. We will be releasing two episodes every day at 10:30am and 6pm until the end of the build. With the final demo by Toby James and Phil Walker on Saturday. Enjoy!
We'd like to thank our partners for helping to make this video series possible.
Triton Tools - http://www.tritontools.com/en-GB
Wagner Meters - https://www.wagnermeters.com/
ISOtunes Bluetooth Hearing Protection - http://bit.ly/36YmKro
Support us by supporting our Partners, and at the same time get yourself a great deal with ISOtunes. Use code "CRIMSON10" for £10 off at "isotunes.co.uk" or $10 off at "isotunes.com"
Get the Freshest CA glues in the market (USA orders) at www.starbond.com
Use Code 'CRIMSONGUITAR' at checkout to save 15% off on your purchase https://www.starbond.com/?rfsn=4953733.fb5f31 _________________________________________________________________________________________
WEBSITE: http://www.crimsonguitars.com
Luthier’s Tools & Supplies: http://bit.ly/LuthTools
Guitar Building Courses: http://bit.ly/LuthierySchool
Kit Guitars: http://bit.ly/KitGuitars
SOCIAL
Instagram - https://www.instagram.com/crimsonguitars/
Facebook -https://www.facebook.com/CrimsonCustomGuitars/
As always, thank you so much to our Patrons, who help make videos like this possible.
Patreon –https://www.patreon.com/crimsonguitars
OTHER Ben's Vintage Tool Shop - https://vintagetoolshop.com/
Thank you again for all your support, we really, really appreciate it! – Ben
Stay tuned and stay awesome! _________________________________________________________________________________________
Please click 'Like' and subscribe. We appreciate your support.
Thanks for watching.
Видео The 9 Hour Build - Ep.1: Preparing the Body and Neck канала Crimson Custom Guitars
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![The 9 Hour Build - Ep.2: Refining the Neck and Attaching the Fingerboard](https://i.ytimg.com/vi/a4X8-zPls7s/default.jpg)
![](https://i.ytimg.com/vi/UnrDqJoBBew/default.jpg)
![Neck Break Angles and Dimensions for a Through Neck Guitar - Podcast 103](https://i.ytimg.com/vi/I8SJhal2Mm4/default.jpg)
![Building an Acoustic Guitar (Full Montage)](https://i.ytimg.com/vi/0l0cbazB1DI/default.jpg)
![The 9 Hour Build - Ep.9: The Final Countdown](https://i.ytimg.com/vi/kn605isAnzI/default.jpg)
![Making a Guitar Mold - Eric Schaefer Guitars - Online Guitar Building School](https://i.ytimg.com/vi/hN0qrtwHP2g/default.jpg)
![Making A Scarf Joint For A Guitar Neck With An Angled Headstock](https://i.ytimg.com/vi/ftjBRxD_uGE/default.jpg)
![Part 1 - Build an electric guitar with Crimson Guitars](https://i.ytimg.com/vi/CXz1vrXi-rE/default.jpg)
![How to Quickly Carve a Guitar Neck | Building the Temple Guitars Router Jig](https://i.ytimg.com/vi/XeMCD6pyjYo/default.jpg)
![Ben's opinion on using oak in a guitar build - Podcast 116](https://i.ytimg.com/vi/qz5asTuDGqM/default.jpg)
![Podcast 80 - The very basics of carving a guitar neck](https://i.ytimg.com/vi/v2k-5wn1bRs/default.jpg)
![Ep 1 - Full Build of the 90 Hour Build - The Complication - the Most Complex Electric Guitar Ever?](https://i.ytimg.com/vi/n5K993xtDos/default.jpg)
![Building a Guitar Body with a Bent Top - Full Time Lapse Build](https://i.ytimg.com/vi/gjcbaiHTQys/default.jpg)
![Make Your Own Electric Guitar Template](https://i.ytimg.com/vi/UyQMktFSemA/default.jpg)
![Applying An Oil Finish On A Guitar Neck](https://i.ytimg.com/vi/rlkfUoWLH_o/default.jpg)
![Is “Handmade” Really Better? CNC vs. Handmade Guitar](https://i.ytimg.com/vi/wfPU42tLruc/default.jpg)
![Tutorials - Ep 1 - How to Carve a Les Paul Style Guitar Top - tools & rough carving](https://i.ytimg.com/vi/qqhwaj3xXx4/default.jpg)
![Ep 1 of 5 - The Re- Edit of the 9 Hour Guitar Challenge! How to Make a Custom Guitar in 9 Hours](https://i.ytimg.com/vi/xG3ymwitayE/default.jpg)
![Ep 1 - Make a Modern Multi-Scale Electro Acoustic Guitar - Fretboard Layout and Fret Slot Cutting](https://i.ytimg.com/vi/C-PML0AOP1o/default.jpg)
![Ep 19 - BoB1 - Insane Guitar Build in 1 Video!](https://i.ytimg.com/vi/bCJVngFwYC0/default.jpg)