How to Build a Workbench. Easy, Cheap & Sturdy 😁

How to Build a Workbench. Build this Cheap, Sturdy Workbench for your Garage. A workbench is a must for your garage or shed. When it comes to building a workbench l needed to satisfy three criteria. The workbench was required to be tough, cheap to build (second hand or reclaimed materials are fine. It doesn't have to look pretty as pretty soon it is going to be trashed) and sturdy enough to take a beating without falling to bits.

Before l go on...

DIY For Knuckleheads Website: https://diyforknuckleheads.com

-------------

SUBSCRIBE to DIY For Knuckleheads and never miss a video again!
http://www.youtube.com/user/shaneconlan1

-------------

Tools l Use: https://diyforknuckleheads.com/tools-resources/

-------------

Mailing Address:

DIY For Knuckleheads
P.O. Box 152
Sawtell,
NSW, 2452
Australia.

-------------
Check out the Latest Swag from our New DIY For Knuckleheads Clothing and Accessorie Store!
https://shop.spreadshirt.com.au/DIYForKnuckleheads/

------------

Check us out on Facebook;
https://www.facebook.com/DiyForKnuckleheads/

----------

Music supplied by Jason Shaw at www.audionautix.com
Released under Creative Commons License 3.0.
Music Titles: Jennys Theme and Banjo Short

Tools and Materials Required for this Project. Bench approx. 2.2 metres long, 700mm wide and 1.0 metre high.

For the legs: 90mm x 35mm (4 x 1½") pine. Two at 3.6metres (approx 11' 12". I think that reads 11 feet, 12 inches)
For the frame: 90mm x 35mm (4" x 1 ½") Eight at 2.4metres (8 feet)
For the edge trimming: 42mm x 19mm dressed pine. Six at 2.4metres (8 feet)
Ply for bench top and shelf: One sheet at 2.4metres (8 feet) x 1.2metres (47 inches) x 17mm.
Bolts for frame: Eight cuphead bolts at 100mm (4 inches) x 10mm with washers and nuts.
Screws to assemble the workbench: 120 x 65mm Phillips head screws.

Dimensions of Workbench:
Overall width of bench top including pine trim: 690mm (27 inches)
Overall length of benchtop: 2.0metres (78 ½ inches)
Overall height of workbench including the 17mm benchtop: 900mm (35 ½ inches)
Overall width of frame: 570mm ( 22 ½ inches)
Overall length of frame: 1880mm (6' 2 inches)
Overall height of workbench leg (which includes the top rail as it is checked into the leg) 880mm (34 ½ inches)

Tools:
Handsaw, circular saw or drop saw.
Powered or cordless drill.
10mm (4 inch) drill bit.
1/8th countersinking drill bit.
No.2 Phillips Head bit.
Spanner to tighten nuts.
Set Square
Builders Square
Tape Measure
Pencil
Spirit Level
Wood workers Glue.

Cheers,
Uncle Knackers

All Videos produced by shaneconlan1's YouTube Channel are provided for informational purposes only.
All the content provided is for general guidance only. Because tools, products, materials, equipment, techniques, building codes and local regulations are constantly changing, shaneconlan1 cannot, and does not assume any responsibility or liability for the accuracy of the information contained therein. Further, shaneconlan1 (Shane Conlan) will not accept any claim for liability related to, but not limited to, omissions, errors, injury, damage or the outcome of any project. The viewer must always take proper safety precautions and exercise caution when taking on any project. If there are any questions or doubt in regards to the element of a project, please consult with a licensed professional.

Видео How to Build a Workbench. Easy, Cheap & Sturdy 😁 канала DIYForKnuckleheads