Replacing Rear Struts on a 98 Mazda 626 GF 2L Part 1
Part 2: https://youtu.be/nAl00v-kXQM
This is my first attempt at making an instructional video. I've changed front struts on this vehicle after watching a bunch of vids ( heads up to DJDevon ), but didn't find any video on changing the rear struts other than this one for a 93 626 Sedan https://youtu.be/h9Az6H8UkyQ so I thought I'd make one and hope it'll help someone out.
You need a 1/2 inch socket set, and a spanner set, a breaker bar, jack, jack stand, spring compressor, screw driver, WD40. It doesn't hurt to have some cardboard or rubber mats to lay on.
I used the AMPRO T70570 Coil Spring Compressor. You should make sure the threads are clean and then spray them with some WD40 so they move smoothly.
Видео Replacing Rear Struts on a 98 Mazda 626 GF 2L Part 1 канала sailorbob74133
This is my first attempt at making an instructional video. I've changed front struts on this vehicle after watching a bunch of vids ( heads up to DJDevon ), but didn't find any video on changing the rear struts other than this one for a 93 626 Sedan https://youtu.be/h9Az6H8UkyQ so I thought I'd make one and hope it'll help someone out.
You need a 1/2 inch socket set, and a spanner set, a breaker bar, jack, jack stand, spring compressor, screw driver, WD40. It doesn't hurt to have some cardboard or rubber mats to lay on.
I used the AMPRO T70570 Coil Spring Compressor. You should make sure the threads are clean and then spray them with some WD40 so they move smoothly.
Видео Replacing Rear Struts on a 98 Mazda 626 GF 2L Part 1 канала sailorbob74133
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
1998 Nissan Almera 1.6L Primary and Secondary Ignition Snaps and Wacky O2 SwitchesRelative Compression Test Using A PicoScope 2204A Voltage Vs AmperagePart 2: Mazda 626 Suspected Timing Belt Noise from a bad Tensioner or Tensioner SpringAlmera N15 Lambda Spark data: Bad Gas Mileage Part 1DIY Pressure Transducer Signal Noise99 Nissan Almera O2 and Injector Waveforms1999 Nissan Almera Injector and Primary Ignition Waveforms1998 Nissan Almera O2 Pegged High then Low with Fast OscilationsPart 1: Mazda 626 Suspected Timing Belt Noise from a bad Tensioner or Tensioner SpringDIY Pressure Transducer Signal Noise With 0.1uF Capacitor between signal and 0V reference ( ground )98 Mazda 626 GF ( European ) O2 Oxygen Sensor Waveform1998 Nissan Almera 1.6L O2 Inj1 Hacksaw / Misfire Pattern Post Vacuum Leak Fix1999 Nissan Almera Primary & Secondary Ignition Waveforms Cylinder #41998 Mazda 626 2L GF Primary Ignition and Current Ramp Waveforms Throttle SnapsHow to Replace the Tie Rod Dust Boot on a 99 Nissan Almera Part 2Part 5: Mazda 626 Oscilllation in the Timing Belt1998 Nissan Almera 1.6L Alternator Post Voltage AC Coupled + Amperage WaveformAlmera N15 Lambda Scope data: Bad Gas Mileage Part 2DIY Pressure Transducer Final Fix For Power Supply NoiseStrut Replacement Lessons Learned Part 3Looking for the source of a rough idle under load on a 98 Mazda 626