E46 320d 136hp - VP44 fuel pump removal
This is a long video describing how to pull out a VP44 fuel pump from BMW 320D 136 hp (2001 pre-lift version).
I'm doing this first time in my life so i took me about 4 hours, video is cut to 45 minutes.
You essentially need two special tools for removal:
- Crank shaft locking pin
- Fuel pump sprocket removal tool for BMW
And
- Torque wrench
- Normal set of tools
Now in my case i did run into some problems, the aftermarket dual mass fly wheel did NOT have the BMW indent for the tool so i had quite a bit of problems when mounting the pump back in - but i managed it and the car works just fine.
The process is relatively simple and brakes down into following steps:
- Set your engine first cylinder in top position
- Slide in crankshaft locking pin (it should click into indent)
- Marker on Cam shaft should point uppwards parrael to your cylinders (renember engine sits in the chassies at an angle!)
- Lock the pump in using special screw
- Detach pump sprocket using special tool
- Remove fuel pump
IF these steps are done correctly, you wont need any special tools when placing the pump back in. In other case you may need a clock sensor to adjust your pump static angle
Видео E46 320d 136hp - VP44 fuel pump removal канала Przemysław Wilkutowski
I'm doing this first time in my life so i took me about 4 hours, video is cut to 45 minutes.
You essentially need two special tools for removal:
- Crank shaft locking pin
- Fuel pump sprocket removal tool for BMW
And
- Torque wrench
- Normal set of tools
Now in my case i did run into some problems, the aftermarket dual mass fly wheel did NOT have the BMW indent for the tool so i had quite a bit of problems when mounting the pump back in - but i managed it and the car works just fine.
The process is relatively simple and brakes down into following steps:
- Set your engine first cylinder in top position
- Slide in crankshaft locking pin (it should click into indent)
- Marker on Cam shaft should point uppwards parrael to your cylinders (renember engine sits in the chassies at an angle!)
- Lock the pump in using special screw
- Detach pump sprocket using special tool
- Remove fuel pump
IF these steps are done correctly, you wont need any special tools when placing the pump back in. In other case you may need a clock sensor to adjust your pump static angle
Видео E46 320d 136hp - VP44 fuel pump removal канала Przemysław Wilkutowski
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Bosch VP 44 Removal on BMWBMW Diesel Fuel Pump Removal for BMW 335D and X5 35DVP44PSG5 driver of fuel pomp repairJak sprawdzić napięcie sterownika pompy BOSCH VP44 i VP30REPARACION TOTAL VP44 - Llámenos 960061479 - 660562832 www.reparaciontotalvp44.comBMW E90 320D Crank Pulley Removal & Replacementvp 44 bosch bmw 320 136hpBmw 320d 136hp chain distribution noise problem!BMW 320d E46 Diesel Filter Replacement (fixed my power loss!)BMW Hochdruckpumpe wechseln | HD-Pumpe M57 M47 Motor defekt ( Tutorial )BMW E46 Will Not Start? Step By Step Fuel Pump Replacement 316i 318i 320i 323i 325i 328i 330i M3VP44 настройка зажигания с помощью штангеляDesarmado de Bomba VP44BMW 320d e46 1999 136CV disassemble the intake manifoldBomba de inyeccion VP44 Sincronizacion y comienzo de inyeccion BIPРемонт автомобиля BMW 320D 1999, замена приводных цепей ЧАСТЬ ВТОРАЯ.Camshaft and Hydraulic Lifter / Árbol de levas y Taqués Hidráulicos BMW 320d M47R(204D1) .BMW E46 320D FL HOW TO RELASE TANK FUEL METER SENSOR- PASSENGER SIDEНасос VP-44. Как проверить клапан опережения и клапан дозатор.test injectoare bmw 320d e46 150hp - M47N engine - 320d injectors leak off test