Ideal Logic F1 Fault How To Repair your combi boiler
Ideal logic low water pressure. Call installer
Today I'm just at an Ideal Logic with low water pressure. So if you get an F1 fault on an Ideal Logic, I'm just going to show you how to top it up, how to fill it up, or how to re-pressurize it.
So if we have a look at the front there, it's showing F1 as a boiler fault. Now I've taken the case off from this boiler, just because it makes it easier for me to show you the pressure gauge. So pressure gauge is there, so if you see on there, it's on zero, all the way down there at zero, and it wants to be up that black line there.
So what you've got bear in mind is, when you fill this up, is not to put too much pressure in. And you see all these valves, this one, there's the yellow one for gas, and then these ones at the back here, don't touch them, leave them alone. So these here are the only ones that you need to touch, so I'm going to explain what happens. So your system is sealed, and every now and again they'll need topping up and more water putting in.
So what we've got here, this pipe here is the cold water mains, so that's your cold pipe coming in. And then when you open this pipe here, this one, it'll allow water into there and round this flexible pipe here, and to there. So now that's still turned off. And as we open this here, as I turn this now in a minute, this pressure gauge will start to go up, and then that F1 fault will go off.
But as I say, you need to be very careful, and do this slowly, because you don't want to put too much pressure in. So I'm going to do it slowly, and I don't know if you can hear that, but water's now going into the system. And as were doing that, that pressure gauge there is going up. So I've only opened it a little bit, just for a demonstration on this video.
So it's saying FL, or F1 sorry, and the gauge is going up, so I'm just going to open this a bit more, and then the boiler's actually fired up. So that means the fault code's gone off, because the boiler's fired up. So I'm going to just switch the boiler off now, just so we can do it without the power on.
So we're just above now, where we're going to be, this will drop down a little bit as we use it. So turn that off fully, and then turn this one off fully. So that is how you filled up your heating, and there you go. So when I turn the power back on again, you see your fault codes have gone off, and then the boiler will just work now, as normal.
So we're just here today, I'm just going to do a service on this. So that's how you top up, fill up, and re-pressurize your Ideal Logic Combi boiler. Hope that was useful, thanks for watching. http://cchleeds.co.uk/services/boiler-installation
Видео Ideal Logic F1 Fault How To Repair your combi boiler канала Allen Hart
Today I'm just at an Ideal Logic with low water pressure. So if you get an F1 fault on an Ideal Logic, I'm just going to show you how to top it up, how to fill it up, or how to re-pressurize it.
So if we have a look at the front there, it's showing F1 as a boiler fault. Now I've taken the case off from this boiler, just because it makes it easier for me to show you the pressure gauge. So pressure gauge is there, so if you see on there, it's on zero, all the way down there at zero, and it wants to be up that black line there.
So what you've got bear in mind is, when you fill this up, is not to put too much pressure in. And you see all these valves, this one, there's the yellow one for gas, and then these ones at the back here, don't touch them, leave them alone. So these here are the only ones that you need to touch, so I'm going to explain what happens. So your system is sealed, and every now and again they'll need topping up and more water putting in.
So what we've got here, this pipe here is the cold water mains, so that's your cold pipe coming in. And then when you open this pipe here, this one, it'll allow water into there and round this flexible pipe here, and to there. So now that's still turned off. And as we open this here, as I turn this now in a minute, this pressure gauge will start to go up, and then that F1 fault will go off.
But as I say, you need to be very careful, and do this slowly, because you don't want to put too much pressure in. So I'm going to do it slowly, and I don't know if you can hear that, but water's now going into the system. And as were doing that, that pressure gauge there is going up. So I've only opened it a little bit, just for a demonstration on this video.
So it's saying FL, or F1 sorry, and the gauge is going up, so I'm just going to open this a bit more, and then the boiler's actually fired up. So that means the fault code's gone off, because the boiler's fired up. So I'm going to just switch the boiler off now, just so we can do it without the power on.
So we're just above now, where we're going to be, this will drop down a little bit as we use it. So turn that off fully, and then turn this one off fully. So that is how you filled up your heating, and there you go. So when I turn the power back on again, you see your fault codes have gone off, and then the boiler will just work now, as normal.
So we're just here today, I'm just going to do a service on this. So that's how you top up, fill up, and re-pressurize your Ideal Logic Combi boiler. Hope that was useful, thanks for watching. http://cchleeds.co.uk/services/boiler-installation
Видео Ideal Logic F1 Fault How To Repair your combi boiler канала Allen Hart
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
IDEAL Logic low pressure fault | Refill tutorialHow To Top Up The Pressure On Your Ideal BoilerHow to Repair or fix the F1 Fault your ideal Logic Combi BoilerJan fixes the Combi boiler.Combi Boiler Too Much Pressure - How to reduce the water pressure - Central HeatingGas Training - Noisy Ideal Logic Boiler L2 Fault / F2 FaultIdeal Heating | How to Refill Your BoilerCombi boiler not working? an easy fix,using the refill pressure loop.Gas Training - Boiler Repairs - Ideal Logic / Ideal Vogue L2 Fault Code F2Gas Training - How An Ideal Logic Works - Hydroblock / Diverter Valve - Viva Training AcademyHeating system tripping electricsHow to Repair your Ideal Logic Plus Combi boilerBOILER KEEPS LOSING PRESSURE - WHY AND HOW TO FIX - Plumbing tipsIdeal Logic. Low Water Pressure. Boiler Stopped working. How to get your boiler working again. 2021How To Bleed A Radiator - Don’t try it until you watch thisBOILER LOSING PRESSURE - Combi boiler keeps losing pressure?How to take some of the pressure out of your Combi boilerLogic combi 30 F2 & L2 fault fixedHow To Top Up Pressure On Ideal Logic Combi 30kw Boiler