Troubleshooting a Furnace Inducer Motor (The 4 Most Common Problems in 2021)
Troubleshooting a Furnace Inducer Motor will walk you step by step to see if you have a bad inducer motor. The 4 most common problems that make inducer motors fail are discussed in this video. HVAC training videos like this will help you diagnose common problems with the gas furnace.
When a furnace begins a new cycle, the inducer motor is the first thing you should see kick on. 120 volts is applied through the wires coming from the control board. This starts the inducer motor for up to 60 seconds before anything else even happens. It’s a safety feature that creates a negative pressure or draft which purges the heat exchanger of any poisonous gasses, namely the biproducts of combustion. It makes the air inside the heat hollow tubes of the heat exchanger cleaner when the flame kicks on. When we have cleaner air inside the heat exchanger at the time of combustion the efficiency of the furnace increases.
The 4 reasons an inducer motor can fail are:
1. The shaft of the inducer motor could be seized up
2. The inducer motor could have an open winding
3. The capacitor could be bad, (If it has one)
4. If it starts making loud or odd noises, like rattling noise, a clanking noise, chattering, pinging, shaking, a wobbling noise
Because many inducer motors are nearly impossible to rebuild, an entirely new unit must be purchased in most cases when one wears out. One of the exceptions to this is the occasional Carrier or Bryant units.
During installation of the inducer motor, we need to make sure to either replace the gasket, (usually comes with the new motor), or make a gasket with high temp silicone. Once installed, a good technician will test the system for proper operation to make sure there are no other issues with the furnace.
So, just to recap, inducer motors pull the flame through the heat exchanger and vent the exhaust through the roof. In order to determine failure of an inducer motor, we need to verify the proper voltage is being sent to it. If the motor has proper voltage, the capacitor tests good, and is not turning on, the motor is bad. If it’s making a lot of noise, the homeowner should know the part is working but is on borrowed time.
Please visit our website @ http://www.foxfamilyhvac.com
If you'd like to book an appointment with Fox Family Heating and Air in Sacramento, El Dorado, or Placer County, CA https://book.housecallpro.com/book/Fox-Family-Heating-and-Air-Conditioning/babd3396dba440e1afac01c631d95f1d
Call or text us at (916) 877-1577 to schedule an appointment.
0:00 Intro
0:40 Disclaimer
1:23 Sequence of events
2:00 The inducer motor
3:00 How to troubleshoot the inducer motor
5:16 What to do next
6:25 Final steps
8:26 Recap
=============================================
→ Disclaimer
Portions of stock footage of products was gathered from multiple sources including, manufactures, fellow creators and various other sources. HousecallPro compensates Fox Family should you like what you see in your free demo and sign up with them for 30 days.
Видео Troubleshooting a Furnace Inducer Motor (The 4 Most Common Problems in 2021) канала Fox Family Heating and Air Conditioning
When a furnace begins a new cycle, the inducer motor is the first thing you should see kick on. 120 volts is applied through the wires coming from the control board. This starts the inducer motor for up to 60 seconds before anything else even happens. It’s a safety feature that creates a negative pressure or draft which purges the heat exchanger of any poisonous gasses, namely the biproducts of combustion. It makes the air inside the heat hollow tubes of the heat exchanger cleaner when the flame kicks on. When we have cleaner air inside the heat exchanger at the time of combustion the efficiency of the furnace increases.
The 4 reasons an inducer motor can fail are:
1. The shaft of the inducer motor could be seized up
2. The inducer motor could have an open winding
3. The capacitor could be bad, (If it has one)
4. If it starts making loud or odd noises, like rattling noise, a clanking noise, chattering, pinging, shaking, a wobbling noise
Because many inducer motors are nearly impossible to rebuild, an entirely new unit must be purchased in most cases when one wears out. One of the exceptions to this is the occasional Carrier or Bryant units.
During installation of the inducer motor, we need to make sure to either replace the gasket, (usually comes with the new motor), or make a gasket with high temp silicone. Once installed, a good technician will test the system for proper operation to make sure there are no other issues with the furnace.
So, just to recap, inducer motors pull the flame through the heat exchanger and vent the exhaust through the roof. In order to determine failure of an inducer motor, we need to verify the proper voltage is being sent to it. If the motor has proper voltage, the capacitor tests good, and is not turning on, the motor is bad. If it’s making a lot of noise, the homeowner should know the part is working but is on borrowed time.
Please visit our website @ http://www.foxfamilyhvac.com
If you'd like to book an appointment with Fox Family Heating and Air in Sacramento, El Dorado, or Placer County, CA https://book.housecallpro.com/book/Fox-Family-Heating-and-Air-Conditioning/babd3396dba440e1afac01c631d95f1d
Call or text us at (916) 877-1577 to schedule an appointment.
0:00 Intro
0:40 Disclaimer
1:23 Sequence of events
2:00 The inducer motor
3:00 How to troubleshoot the inducer motor
5:16 What to do next
6:25 Final steps
8:26 Recap
=============================================
→ Disclaimer
Portions of stock footage of products was gathered from multiple sources including, manufactures, fellow creators and various other sources. HousecallPro compensates Fox Family should you like what you see in your free demo and sign up with them for 30 days.
Видео Troubleshooting a Furnace Inducer Motor (The 4 Most Common Problems in 2021) канала Fox Family Heating and Air Conditioning
Показать
Комментарии отсутствуют
Информация о видео
5 декабря 2020 г. 22:59:32
00:09:01
Другие видео канала
Inducer Motor Not Coming On - How to Check ItTop 8 Inducer Motor Noise Problems on a Gas Furnace!Gas Furnace NOT flooded big HVAC scam ripoffHow to Diagnose a Bad Furnace Pressure Switch (5 Easy Things to Check in 2021)Furnace Pressure Switch TroubleshootingChanging an 80 Percent Furnace Induced Draft MotorTop 4 Reasons Why a Gas Furnace Short Cycles! HVACR Service Call Troubleshooting Tips!Furnace Starts Then Stops - Troubleshooting | Repair and ReplaceNo Heating Trane Gas Furnace False High Limit Error CodeTop 5 Furnace Problems and How to Fix ThemFurnace Inducer Motor Troubleshooting! Top 8 Problems!Screeching Furnace Repair - Carrier Draft Inducer Motor Replacement in 4KFurnace/AC How to Troubleshoot The Control BoardNoisy Furnace? - Top 5 Fixes | Repair and ReplaceTOP 10 Gas Furnace, PRESSURE SWITCH Error Code Problems!Goodman Gas Furnace making noiseHVAC Pressure Switch Opened or ClosedNo Heat Service Call Clogged Vac Port on Inducer MotorFurnace Overheating - 10 Reasons WhyGas Furnace Won't Turn On? Nothing Happening? 8 Reasons Why!