(7/10) CC3D Flight Controller - Adding a buzzer with a CPPM/PPM receiver (ADVANCED)
To see all of the videos in this series visit https://www.youtube.com/playlist?list=PLYsWjANuAm4r-E61stLchCR4bzY3NmDNh
This video was created after requests from subscribers.
This video series has been created for first time builders so they can understand where each piece of a build fits and follow each of the steps easily. However due to the complex nature of this setup I would recommend that you use the similar method for adding a Buzzer we covered earlier in the series if you are new to building and programming quad copters using the CC3D (https://www.youtube.com/watch?v=LgLndyKYuuI&list=PLYsWjANuAm4r-E61stLchCR4bzY3NmDNh&index=8)
Find the Buzzer on HobbyKing at http://www.hobbyking.com/hobbyking/st...
You can read up about the options for the PPM connection at https://wiki.openpilot.org/display/WIKI/CopterControl+-+CC3D+-+Atom+Hardware+Setup
In this video we will over:
- Introduction (0:02)
- Demo of it working (0:28)
- How to wire up the buzzer and PPM/CPPM receiver (2:34)
- CPPM pin options (pin 3 or Pin 8) (3:08)
- Configuration in Openpilot (3:54)
- Setting up the Rcvrport (4:46)
- Setting up the input channels (6:21)
- Quick overview of TARANIS model setup (7:12)
- Setting up the output we want to use for the buzzer (8:31)
- Configure the PWN range of the output channel (10:03)
- Quick recap on steps (10:40)
- Summary and demo (11:23)
Thank you for watching, please LIKE and SUBSCRIBE.
Happy flying!
Видео (7/10) CC3D Flight Controller - Adding a buzzer with a CPPM/PPM receiver (ADVANCED) канала Painless360
This video was created after requests from subscribers.
This video series has been created for first time builders so they can understand where each piece of a build fits and follow each of the steps easily. However due to the complex nature of this setup I would recommend that you use the similar method for adding a Buzzer we covered earlier in the series if you are new to building and programming quad copters using the CC3D (https://www.youtube.com/watch?v=LgLndyKYuuI&list=PLYsWjANuAm4r-E61stLchCR4bzY3NmDNh&index=8)
Find the Buzzer on HobbyKing at http://www.hobbyking.com/hobbyking/st...
You can read up about the options for the PPM connection at https://wiki.openpilot.org/display/WIKI/CopterControl+-+CC3D+-+Atom+Hardware+Setup
In this video we will over:
- Introduction (0:02)
- Demo of it working (0:28)
- How to wire up the buzzer and PPM/CPPM receiver (2:34)
- CPPM pin options (pin 3 or Pin 8) (3:08)
- Configuration in Openpilot (3:54)
- Setting up the Rcvrport (4:46)
- Setting up the input channels (6:21)
- Quick overview of TARANIS model setup (7:12)
- Setting up the output we want to use for the buzzer (8:31)
- Configure the PWN range of the output channel (10:03)
- Quick recap on steps (10:40)
- Summary and demo (11:23)
Thank you for watching, please LIKE and SUBSCRIBE.
Happy flying!
Видео (7/10) CC3D Flight Controller - Adding a buzzer with a CPPM/PPM receiver (ADVANCED) канала Painless360
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![RC Quick Tip - PWM, PPM, CPPM, S-BUS and Sat. explained for beginners](https://i.ytimg.com/vi/GbUMC8h2uhU/default.jpg)
![CC3D Flight Controller Wiring Connection Explained](https://i.ytimg.com/vi/KjG6FKCNCbM/default.jpg)
![Discovery Buzzer - Receiver Connected](https://i.ytimg.com/vi/EcATaRdRbHU/default.jpg)
![(1/10) CC3D Flight Controller for Beginners - Overview, frame build and power setup](https://i.ytimg.com/vi/ZK7IkctChu8/default.jpg)
![(4/10) CC3D Flight Controller - Adding an OSD using MinimOSD](https://i.ytimg.com/vi/8GFcS4_XcP8/default.jpg)
![CC3D Quick Tip - Mounting sideways (90 degrees) for easier USB access](https://i.ytimg.com/vi/YHkndsgNbVU/default.jpg)
![(6/10) CC3D Flight Controller – Loading Cleanflight onto your CC3D](https://i.ytimg.com/vi/DRm_CyAyKcs/default.jpg)
![Using 3 Wire Buzzer With Betaflight / Cleanflight](https://i.ytimg.com/vi/k1qwmxY7d9s/default.jpg)
![RC Quick Tip - Adding a Lost Model Alarm / Buzzer](https://i.ytimg.com/vi/4stL9_LQGzI/default.jpg)
![](https://i.ytimg.com/vi/d7PTL9c8sJM/default.jpg)
![Introduction to CC3D - Flight mode overview (rate, attitude, acro+ rattitude etc)](https://i.ytimg.com/vi/pyi7brefxVs/default.jpg)
![How to wire and setup flysky Ibus in betaflight // Under 5 Minutes](https://i.ytimg.com/vi/bo54uOETE_I/default.jpg)
![How to power a CC3D flight controller (3.7-5V DC)](https://i.ytimg.com/vi/JGkYRy4-g9U/default.jpg)
![How to configure Open Pilot CC3D Flight Controller with Ground Controller Station v14.10 Mini Me](https://i.ytimg.com/vi/DEQY9gHb50s/default.jpg)
![CC3D - Aggiungere Buzzer e LED attivabili con switch o Failsafe (ricevente ppm o s.bus)](https://i.ytimg.com/vi/0bnKoXI9X6s/default.jpg)
![Teil 4 // Wir bauen einen Race Quad ZMR250 //Fpv Empfänger CC3D Anschluss // 20A Esc //](https://i.ytimg.com/vi/blc9VZ4rhL8/default.jpg)
![Setting up buzzer for rx_lost and switch](https://i.ytimg.com/vi/3TURGyJ3-pM/default.jpg)
![What Are Aux Channels and How to Set Up Flysky FS-i6X Aux Switches](https://i.ytimg.com/vi/JZQoHmLqZYg/default.jpg)
![RadioLink AT9-R9D + APM. How to connect receiver to flight controller ?](https://i.ytimg.com/vi/-UwyhqZnDSk/default.jpg)
![Putting Matek WS2812b In Programmable Mode For Cleanflight](https://i.ytimg.com/vi/EN5I-KTewE4/default.jpg)