WELDY energy 1600 for welding PE, PP and PVC plastic sheets
WELDING TIPS:
The most important rule in plastic welding is that it is only possible to weld like.
Hence the need to identity plastic material and select a matching welding rod.
The main welding operation begins with preparation of the welding rod. Cut the end To a pencil point using a trimming knife or side cuters; this provides a progressive fill in V groove, particularly where it starts in the centre of a panel, preventing the formation Of bulbous protrusions of plastic.
Fit speed welding nozzle to the WELDY energy tool, set the correct temperature for the Material and allow the tools to warm up for a few minutes before starting.
Insert the trimmed welding rod through the nozzle feeder until approximately 5mm protrudes on the underside. Hold the tool so that the speed welding nozzle sole runs along The crack parallel to the component surface.
The protruding rod must be held beyond the start of the V groove so the heat is directed onto the start point
for welding.
When the surface plastic shows signs of slight wetting move the welding nozzle along the groove. The nozzle toe should rest on the rod in the groove while under the heel there should be an air gap of 3mm. Feed the rod steadily into the nozzle with a downward hand pressure of about 2.5 kg sufficient to push the softened rod into the groove. To judge what a pressure of 2.5kg feels like, take a short piece of weld rod and use it to press down on an set scales until 2.5 kg registers. (Do not apply downward force to the weld via the hot air tool itself). Wherever possible the weld should be completed in one continuous run along the contour of the crack.
Wish you a good welding!
WELDY energy 1600 hot air hand tool, compact and robust - plastic welding kit
The energy 1600 plastic welding kit: Your hot air equipment for welding PE, PP and PVC plastic sheets.
Main applications:
- Plastic fabrication
- Flooring
- Car repair
- Joining pipes
- Welding PVC-floors
• Free adjustable temperature
• Heating tube protection for more security
• Economical and universal
www.weldy.com
simple. good. affordable.
Видео WELDY energy 1600 for welding PE, PP and PVC plastic sheets канала WELDYhotairtools
The most important rule in plastic welding is that it is only possible to weld like.
Hence the need to identity plastic material and select a matching welding rod.
The main welding operation begins with preparation of the welding rod. Cut the end To a pencil point using a trimming knife or side cuters; this provides a progressive fill in V groove, particularly where it starts in the centre of a panel, preventing the formation Of bulbous protrusions of plastic.
Fit speed welding nozzle to the WELDY energy tool, set the correct temperature for the Material and allow the tools to warm up for a few minutes before starting.
Insert the trimmed welding rod through the nozzle feeder until approximately 5mm protrudes on the underside. Hold the tool so that the speed welding nozzle sole runs along The crack parallel to the component surface.
The protruding rod must be held beyond the start of the V groove so the heat is directed onto the start point
for welding.
When the surface plastic shows signs of slight wetting move the welding nozzle along the groove. The nozzle toe should rest on the rod in the groove while under the heel there should be an air gap of 3mm. Feed the rod steadily into the nozzle with a downward hand pressure of about 2.5 kg sufficient to push the softened rod into the groove. To judge what a pressure of 2.5kg feels like, take a short piece of weld rod and use it to press down on an set scales until 2.5 kg registers. (Do not apply downward force to the weld via the hot air tool itself). Wherever possible the weld should be completed in one continuous run along the contour of the crack.
Wish you a good welding!
WELDY energy 1600 hot air hand tool, compact and robust - plastic welding kit
The energy 1600 plastic welding kit: Your hot air equipment for welding PE, PP and PVC plastic sheets.
Main applications:
- Plastic fabrication
- Flooring
- Car repair
- Joining pipes
- Welding PVC-floors
• Free adjustable temperature
• Heating tube protection for more security
• Economical and universal
www.weldy.com
simple. good. affordable.
Видео WELDY energy 1600 for welding PE, PP and PVC plastic sheets канала WELDYhotairtools
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Plastic welding, custom RV tanks, part 1 of 2Plastic Hot Air Welding of PVC Ventilation Pipe & PittingsHeat Weld Vinyl Installation. Best On Youtube.Plastic welding with Bak RionPistolet Herz Weldon do spawania tworzyw sztucznych na przykład PP ( polipropylen)How to use a Harbor Freight Plastic Iron Item 60662Plastic Welding: How To Instructional Video by TechspanLearn Plastic Welding » Weld and repair a garbage bin with a plastic welderKunststof PVC lassen. Hechtlassen met Almond BAK RionWelding Workers Who Are Professional and Experts Of High Level ▶5WELDY - Easy Tarpaulin and Banner weldingAIT induction - Hot Air plastic repair - Collision Repair LineMakita Heat Guns | Kaisertech LtdBumper Repair with Hot Air Plastic WelderAMAZING! Top 2 Ideas from PVC Pipe 110 mm!230V 1600W Hot Air Welding Tools and Machines for PVC Welding |plastic welding machine | Hot gunDelboy's Garage, Simple skills # Plastic weldingWELDY leak tightness testerTOP 5 Best Plastic Welders 2021 💥 Best Plastic Welders 💥How To Make Water Pump At Home,Water Pump From PVC Pipe/V6