Lead Acid Battery Repair in 2 Minutes | Revive and Charge 6v 12v (Jump Repair)

Welcome to Handy Dandy Daddy and today’s video is about Lead Acid Battery Repair in 2 Minutes, Revive and Charge 6v 12v with Jump Repair.

Do you have an old or dead 6V/12V lead acid battery? It’s time to revive your dead battery. Reviving batteries is an important money and time saver. You can extend the life of your battery by reuse it.

▶️ CHECK THE LINKS BELOW FOR THE GEAR USED:
• Gears used: https://amzn.to/3hsiLs1
• Battery pack - https://amzn.to/2WyIHue
• Power wheel batteries - https://amzn.to/39aBTIj
• Battery trickle charger - https://amzn.to/2CpTiAD

In this video we are going to show you how refurbish a car battery in 2 minutes. We turn this 12V lead dead dry battery like a new battery with a few steps. So, follow our Lead Acid Battery Repair in 2 Minutes tutorial.

▶️What you needed for repairing lead acid battery :
• Safety Glasses (So you don't get mild battery acid in your eyes (like I did))
• Funnel or something to put water into the cells
• Very small flat-head screwdriver
• Needle-nosed pliers
• Battery Charger (optional)
• De-ionized water (you can use tap water but it's not reccommended)

▶️Method and Instructions:
• Open the top lid of the dead battery
• Fill the dry battery with distilled water
• Close lid and attempt charge
• Use jump start with battery pack if needed
• Keep it charged for 5 hours

▶️Method and Instructions in details:
• Pry Off the Cover
• Use the small flat head screwdriver to pry off the cover, There are usually some slots that it will fit in.
• Take the Cell Vents Off
• Using your needle nosed pliers, Pull off the rubber vent covers.
• Be careful because this could spit battery acid at you
• Add Water to the cells
• For this step use your safety glasses
• Add De-ionized water/water to the cells by using your funnel or similar.
• Put the Rubber Caps Back on and Charge
• Put all the caps back on the cells.
• Connect to a battery charger and put a towel or rag over the SLA in case it was filled to much and needs to vent, If it vents it will probably pop off the rubber caps, Just put them back on.
• Put the Cover Back On
• Once you have checked the battery is good, Put the cover back on.
• Use any type of mild to strong adhesive to stick the cover to the battery, remember not to fully seal the top so that the gases can escape.

Now you're done!

Let us know by commenting, how good/bad your refilled battery has performed.

If you like my video, please SUBSCRIBE and don’t forget to press the bell, 🔔 like, comment and share. Stay safe and Love all. 😍
------------------------------------------------------------
▶️ Please Subscribe: https://www.youtube.com/channel/UC-o2y8_v-TsuAnM0arw7MYA/featured
------------------------------------------------------------------
▶️My other videos:
• Install ceiling fan with light: https://youtu.be/XRI89mUTRSM
• Spectacular Modern Home Tour: https://youtu.be/cXyyb3p4mNk
-----------------------------------------------------------
▶️ About Handy Dandy Daddy:
Presenting you vlogs of different projects we do in and around our household. Please consider subscribing to watch new videos as we make them available.
-----------------------------------------------------------
▶️ For business enquiries: classiqueentertainments@gmail.com
----------------------------------------------------------------
#leadacidbattery #HandyDandyDaddy #leadacidbatteryrepair #12vleadacidbattery #6vleadacidbattery #acidbattery #revivecarbattery #deadleadacidbatteryrepair

Видео Lead Acid Battery Repair in 2 Minutes | Revive and Charge 6v 12v (Jump Repair) канала Handy Dandy Daddy