I'm cutting a GIANT NOTCH in my 4x4 Drag Truck Chassis
to help the 4wd drag truck build achieve a proper stane, we need the back end to sit a little lower than the stock frame rails will allow, which means its time to install a c-notch! There are a few different notch styles on the market, and I refuse to install a bolt-in notch which means it's time to get out the welder. This drag truck will be powered by a 535 cubic inch Gen 7 big block chevy with a massive turbocharger, and should produce somewhere around 1,500 horsepower when its done. We're shooting for an 8 second 1/4 mile goal, and with the C-notch complete, the rolling chassis is nearly 100% complete.
The c notch kit that I used
https://www.overkillbydesign.com/shop/p/nbs-c-notch-under-bed-frame-kit
I bought an abandoned automotive shop
https://youtu.be/dADqDcT3ps4
Видео I'm cutting a GIANT NOTCH in my 4x4 Drag Truck Chassis канала Lawrence LT Tolman
The c notch kit that I used
https://www.overkillbydesign.com/shop/p/nbs-c-notch-under-bed-frame-kit
I bought an abandoned automotive shop
https://youtu.be/dADqDcT3ps4
Видео I'm cutting a GIANT NOTCH in my 4x4 Drag Truck Chassis канала Lawrence LT Tolman
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![New Wheel Wednesday](https://i.ytimg.com/vi/672OFrCDOBU/default.jpg)
![1970 GTO Judge(?) back from the dead at RedShift](https://i.ytimg.com/vi/uba1RLhi6vM/default.jpg)
![GTX40 LMM dyno run: 707 hp at the wheels](https://i.ytimg.com/vi/XENzPG9ZQSY/default.jpg)
![1,000hp fuel system for the Turbo Big Block](https://i.ytimg.com/vi/cwHyuXI4XT4/default.jpg)
![the MONSTER BIG BLOCK gets some MASSIVE MOTOR MOUNTS](https://i.ytimg.com/vi/T6Jh1sy86Rw/default.jpg)
![Fixing a bad Exhaust Leak on the Turbo 8.1 UglyTruck](https://i.ytimg.com/vi/PocrYJbXJ2c/default.jpg)
![4.8 build-off begins!](https://i.ytimg.com/vi/gSlVl87oVYM/default.jpg)
![DIY Stainless Pie Cut Exhaust for the Turbo 8.1 Vortec](https://i.ytimg.com/vi/N_-_QN241Cg/default.jpg)
![Building Intercooler Pipes for the 8.1 Turbo Silverado](https://i.ytimg.com/vi/NCx6NJhY3aY/default.jpg)
![Front Suspension Fabrication for a 1,500HP AWD Silverado](https://i.ytimg.com/vi/iWj4eDpPcOA/default.jpg)
![Converter Time! Burnouts pending…](https://i.ytimg.com/vi/5Y9DU92lkc0/default.jpg)
![Interior Makeover for the UglyTruck](https://i.ytimg.com/vi/BPvVb7A2jfo/default.jpg)
![4l80 Is getting closer!](https://i.ytimg.com/vi/-eo-mp_vi6c/default.jpg)
![WORLDS BRIGHTEST fog lights + FAILING cam sensor](https://i.ytimg.com/vi/FAkORK1fYC8/default.jpg)
![Drilling Holes in the Transmission](https://i.ytimg.com/vi/di5GrdFi7x0/default.jpg)
![an EASY DIY headlight restoration that will ACTUALLY LAST](https://i.ytimg.com/vi/P6UI_EChFUI/default.jpg)
![Turbo Big Block Autocross: Day 1 of the ProTouring Truck Shootout](https://i.ytimg.com/vi/WzeU0y911PE/default.jpg)
![installing AIR SUSPENSION on my tow rig for a SMOOTH RIDE](https://i.ytimg.com/vi/7MEScdVR-0A/default.jpg)
![351 to 408 Windsor swap in a 1993 F-150: It's almost ready, but it can't go in yet...](https://i.ytimg.com/vi/kVgaSZiPvRA/default.jpg)
![93 F-150 408 Stroker Windsor Swap Accessory Drive ft. New Shop Equipment](https://i.ytimg.com/vi/XvAKcMqySuc/default.jpg)