Rover SD1 V8 3.5 Vanden Plas EFI Engine Rebuild Part 2 - Cylinder heads, hydraulic lifter pre load
Part 2 of the rebuild of a Rover V8 engine. This engine is for a 1985 Rover SD1 Vanden Plas EFI. It is a 3.5 litre unit with 9.75:1 compression ratio.
In this video i installed the cylinder heads, the rocker gear and then adjusted the hydraulic followers / lifter / tappets pre load using a shim kit. Its a bit of a faff, but if you have had your heads skimmed its a good idea.
NOTE: I didnt put any sealer on the threads of the cylinder head bolts. I just used clean engine oil to act as a lube to aid torqueing. The old rover manual says to put 3M EC 776 on the threads, the newer range rover manual says to use Loctite 572. I think this is to stop corrosion of the threads, but not 100% sure. The newest range rover manual for cars with the non re-useable stretch bolts says just use clean engine oil.
Видео Rover SD1 V8 3.5 Vanden Plas EFI Engine Rebuild Part 2 - Cylinder heads, hydraulic lifter pre load канала nitrosilvia
In this video i installed the cylinder heads, the rocker gear and then adjusted the hydraulic followers / lifter / tappets pre load using a shim kit. Its a bit of a faff, but if you have had your heads skimmed its a good idea.
NOTE: I didnt put any sealer on the threads of the cylinder head bolts. I just used clean engine oil to act as a lube to aid torqueing. The old rover manual says to put 3M EC 776 on the threads, the newer range rover manual says to use Loctite 572. I think this is to stop corrosion of the threads, but not 100% sure. The newest range rover manual for cars with the non re-useable stretch bolts says just use clean engine oil.
Видео Rover SD1 V8 3.5 Vanden Plas EFI Engine Rebuild Part 2 - Cylinder heads, hydraulic lifter pre load канала nitrosilvia
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Rover SD1 V8 3.5 Vanden Plas EFI Engine Rebuild Part 3 Front timing cover, oil pump, water pump](https://i.ytimg.com/vi/r51DqB52pqo/default.jpg)
![Rocker Arm/Hydraulic Lifter Adjustment](https://i.ytimg.com/vi/LIfZmC_KwGg/default.jpg)
![Rover V8 hydraulic tappets/lifters. Can you clean them if they have no wear?](https://i.ytimg.com/vi/OGWCKL9BPPM/default.jpg)
![Rover v8 - assessment and measurements pre build](https://i.ytimg.com/vi/2ItQpM6jZkA/default.jpg)
![Kawasaki Z1 Super six Crankshaft - How its Made](https://i.ytimg.com/vi/uW2YFNDjN_o/default.jpg)
![How to - Ticking tapping hydraulic tappets on a Rover v8](https://i.ytimg.com/vi/a7HGGjs6dt4/default.jpg)
![Rover SD1 V8 3.5 Vanden Plas EFI Engine Rebuild Part 1 - Crankshaft and Pistons](https://i.ytimg.com/vi/gOfVYosyvfM/default.jpg)
![Cylinder Head 105 - Valve Job Basics](https://i.ytimg.com/vi/7GEmuQa3dPY/default.jpg)
![How Ignition Coils Work](https://i.ytimg.com/vi/lWyn_eV-DzM/default.jpg)
![Rover v8 hydraulic lifter preload setting and explanation](https://i.ytimg.com/vi/Ol-U4YlWtDc/default.jpg)
![Rover 420 gsi turbo project - Part 11 Trialing the jap spec rear panel](https://i.ytimg.com/vi/X7y_WJgAhiM/default.jpg)
![Dotty 1981 Rover SD1 Restoration - Video 62 Interior fit, gutter rail trims](https://i.ytimg.com/vi/l1ED5kEB_CI/default.jpg)
![How-To: Lap Valves (by hand and drill method explained)](https://i.ytimg.com/vi/taAP7YoVhGo/default.jpg)
![Completely Dismantling A Land Rover V8's Engine | Wheeler Dealers](https://i.ytimg.com/vi/OfdgxPpXD9U/default.jpg)
![Rover 3500 Non EFi Vanden Plas](https://i.ytimg.com/vi/FS0dwvKLnZw/default.jpg)
![Rover V8 3.5L to 4.6L upgrade DYNO TESTED! Rover p6 - Part 7](https://i.ytimg.com/vi/3u05-aYgEFI/default.jpg)
![Dotty 1981 Rover SD1 Restoration - Video 36 Rear lamp panel 1](https://i.ytimg.com/vi/gsj0yL2FOFM/default.jpg)
![Ignition Systems - How they Work | SCIENCE GARAGE](https://i.ytimg.com/vi/742Ml4oD3s4/default.jpg)
![CRAZY Supercharged 390 AMC build. The beginning](https://i.ytimg.com/vi/xdyV3up8ZuM/default.jpg)
![NEC Classic and restoration show 2022 - Day 3, changing gearbox in rover sd1 v8, added FAIL!!!!!!](https://i.ytimg.com/vi/fwTyU1FvP3E/default.jpg)