Emergency Plumbing - stopcock repair in situ
Other related videos:
How to strip and repair tap gland-seal
https://youtu.be/bg_vo6osZfc
How to stop a monobloc tap outlet leaking (emergency repair)
https://youtu.be/RDb9wNvmjig
Earlier today I noticed some water on the floor near the kitchen sink so opened the unit and saw a bit of a leak from the main stopcock that controls flow of water from rising main into the house. Water was dripping from the gland seal. Unfortunately since this is the main way of turning off the water supply* I couldn't isolate the actual stopcock which ironically is the isolating valve for the cold water supply. So as this was an emergency repair I had to use PTFE tape which is a product that everyone should have in their toolkit.
Anyway - to carry out emergency repair;
Turn off the stopcock and remove handle by unscrewing the cross-head screw in the end of shaft.
Loosen off the gland seal retainer collar. The leak will worsen so put some old rags around it to mop up spills.
Try to extract the old gland packing which is either rubber, fibre or leather. If the tap is in awkward place or the old seal is rock hard and too tight to remove, you then have to wrap several turns of PTFE tape around the shaft as near to the gland seal as possible.
Now using a flat screwdriver and carefully push the tape right down into the gland seal (or what's left of it)
Now install the gland seal retainer collar and tighten it up.
Now turn on the stopcock or tap/faucet and check for leaks. Ideally the old seal/packing is removed first but in the real world that sometimes doesn't happen. If there's still no leaks after a few hours then chances are you've fixed the problem. This is a 'temporary repair' so ultimately you will have to fit a new stopcock/tap/valve at some point. A useful tip is to regularly cycle any water supply valves, taps etc fully open and closed to keep them from sticking open or shut. Do this twice a year. Taps tend to seize more when they are fully open so it's good practice to open them fully then back them off half a turn so the internal valve seat isn't hard against the end stops.
*If the main water supply stop valve is leaking you'll either need a pipe freezing kit or hope there is a main water supply cut-off along with the water meter or supply from the mains water. Worth making a note of where the stopcocks and other valves are located on your property.
Видео Emergency Plumbing - stopcock repair in situ канала TK42138
How to strip and repair tap gland-seal
https://youtu.be/bg_vo6osZfc
How to stop a monobloc tap outlet leaking (emergency repair)
https://youtu.be/RDb9wNvmjig
Earlier today I noticed some water on the floor near the kitchen sink so opened the unit and saw a bit of a leak from the main stopcock that controls flow of water from rising main into the house. Water was dripping from the gland seal. Unfortunately since this is the main way of turning off the water supply* I couldn't isolate the actual stopcock which ironically is the isolating valve for the cold water supply. So as this was an emergency repair I had to use PTFE tape which is a product that everyone should have in their toolkit.
Anyway - to carry out emergency repair;
Turn off the stopcock and remove handle by unscrewing the cross-head screw in the end of shaft.
Loosen off the gland seal retainer collar. The leak will worsen so put some old rags around it to mop up spills.
Try to extract the old gland packing which is either rubber, fibre or leather. If the tap is in awkward place or the old seal is rock hard and too tight to remove, you then have to wrap several turns of PTFE tape around the shaft as near to the gland seal as possible.
Now using a flat screwdriver and carefully push the tape right down into the gland seal (or what's left of it)
Now install the gland seal retainer collar and tighten it up.
Now turn on the stopcock or tap/faucet and check for leaks. Ideally the old seal/packing is removed first but in the real world that sometimes doesn't happen. If there's still no leaks after a few hours then chances are you've fixed the problem. This is a 'temporary repair' so ultimately you will have to fit a new stopcock/tap/valve at some point. A useful tip is to regularly cycle any water supply valves, taps etc fully open and closed to keep them from sticking open or shut. Do this twice a year. Taps tend to seize more when they are fully open so it's good practice to open them fully then back them off half a turn so the internal valve seat isn't hard against the end stops.
*If the main water supply stop valve is leaking you'll either need a pipe freezing kit or hope there is a main water supply cut-off along with the water meter or supply from the mains water. Worth making a note of where the stopcocks and other valves are located on your property.
Видео Emergency Plumbing - stopcock repair in situ канала TK42138
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
How to Fix a Leaky Stopcock & Stop Dripping WaterHow to free a jammed stopcock that will not turn.Aladdin EasyFit Isolator | Isolate a live water pipeSeized stop tap. Cutting into mains to replace. Day in the life of a Plumber / Gas EngineerPlumbers Vlog #1 | Nothing is ever simple! | Replacing a Seized StopcockLeaking stop tap repairWater Valve Won't Shut Off Water"Stopcocks" hate them? How about a switch to turn your water off.How to repair a leaking stopcock.How to free a seized Stopcock DON'T DO THIS (even though it worked)How to fix a Leaking Stopcock | How to stop a Dripping StopcockHOW TO INSTALL VALVE ON LIVE WATER PIPEHow To Fix Leaking Shut Off Valve FAST DIY - Avoid PlumberHow to connect flexible tap connectors 2019 | flexi tap tailsYOUR MAINS WATER STOPCOCK - HOW THEY WORK - FIXING LEAKS - Plumbing TipsSURE STOP SHUT OFF VALVES - Plumbing TipsAn Easy way To Free a Seized Stopcock.How to free a stopcock that will not turn off.MDPE MAINS WATER PIPE - ATPLAS CHAMBER - Plumbing TipsHow to strip and repair tap gland-seal