Moving the Huge 30ft long Monarch Lathe into the shop
Well it is finally time and the ground is frozen so I took the opportunity to drag the 37000lb Monarch lathe into the shop and to get it unloaded. Follow along as I get it slung up on the bridge crane and move it off the trailer, into position and lower it to it's new home. I also cover some other projects and some of the things that need done to it to get it operational. Sorry about some of the actual moving footage not making it as the camera battery went dead, the job took a few hours and in the 20degree temps the camera battery wasn't having any of that. Thanks for watching!!
Видео Moving the Huge 30ft long Monarch Lathe into the shop канала bcbloc02
Видео Moving the Huge 30ft long Monarch Lathe into the shop канала bcbloc02
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![First Run of the Big Monarch Lathe and 32" Chuck Install](https://i.ytimg.com/vi/lI8CcLXOGts/default.jpg)
![This Old Barn/Shop October 2020 Update Elastomeric Paint on Wood and Full P Series Pump Rebuild Vids](https://i.ytimg.com/vi/SEHcYwdNZGM/default.jpg)
![The Worst Shop Day Ever :-(](https://i.ytimg.com/vi/0Ako5guyzNg/default.jpg)
![Pontiac Engine Block Welding](https://i.ytimg.com/vi/uNwYdFNDlM8/default.jpg)
![SWAPPING FOR CUTTING TOOLS tubalcain wasting money](https://i.ytimg.com/vi/Wf9yS76xn78/default.jpg)
![More Gantry Crane Building! 3Ton Adjustable Span Gantry Layout and Using a Pattern to Construct](https://i.ytimg.com/vi/p7mIq6mNPNE/default.jpg)
![Cummins 8.3l swap the Hyster Forklift: modifying a drive shaft and building a adapter and cold start](https://i.ytimg.com/vi/258HVnTDosk/default.jpg)
![Cummins Swap the Hyster Part 21: Fabricating The Reverser Linkage, installing Sheet Metal and Seat](https://i.ytimg.com/vi/ctV7cLvE4A0/default.jpg)
![Power scraping, more than just fine tuning, you can fix stuff!](https://i.ytimg.com/vi/OY8Kk4kwj40/default.jpg)
![Well it still ain't good :-) I failed](https://i.ytimg.com/vi/SErdAnepdGY/default.jpg)
![Cummins 8.3L Swap Hyster Forklift Part 14: Super Short & Strong Driveshaft Connection Gear Coupling](https://i.ytimg.com/vi/ky-QXxNXpso/default.jpg)
![One Man Army Monster Mill Move Part 4](https://i.ytimg.com/vi/--Gxookz92Q/default.jpg)
![I am Sorry!](https://i.ytimg.com/vi/ErpjxZf1jwk/default.jpg)
![Lots of chip making .125"DOC .020"Feed Rate 4140 Heat Treated Adapting Flat tappets to Roller Block](https://i.ytimg.com/vi/tuVck2gIEX8/default.jpg)
![Experimental strength welding of cast iron](https://i.ytimg.com/vi/zggrKXRPkyI/default.jpg)
![Making the First chips with the Big Monarch Lathe](https://i.ytimg.com/vi/nPih6AlH0mA/default.jpg)
![Finally a Forklift](https://i.ytimg.com/vi/xHe0hU_PD58/default.jpg)
![How I Machine a Contour With no Original to Copy: Stylus to Finished Part Turbo Wheel Fitment](https://i.ytimg.com/vi/blpKxEkdF38/default.jpg)
![Hammer Strap Drawbar Hitch for 2" Receiver and High Tongue Weight Agricultural Implements](https://i.ytimg.com/vi/ARNyGf3CbBQ/default.jpg)
![Old Machinist Collet Trick](https://i.ytimg.com/vi/baBm22Oi_lw/default.jpg)